Oring IAR-120+ Industrial 802.11b/g Access Point 3.5G VPN Router

Posted on June 20, 2015 by escomco

IAR-120/120+ is a reliable 802.11b/g WLAN Access Point with 2 ports 10/100TX ports router where ETH1 for LAN ETH2 for WAN. It could be confi gured to operate in 3 modes of routing function: Dynamic/Static IP route, PPPoE authentication, and Modem (56K/GPRS/3G/3.5G Modem) dial up. In the mode of Modem dial up, it support both traditional 56K modem and GPRSG/3G/3.5G Modem with USB interface. Users can set up WLAN environment to fulfi ll demands of various applications rapidly by dialing up cellular modems. In addition, IAR-120+ also provides PD feature on ETH2 which is fully compliant with IEEE802.3af P.O.E PD specifi cation. This feature extends the layout up to 100 meters. Therefore, IAR-120/120+ are one of the best solution for applications of wireless communication.

Feature :

High Speed Air Connectivity: WLAN interface support up to 54Mbps link speed
Provide HNAT enhance LAN to WAN routing performance
Highly Security Capability: WEP/WPA/WPA-PSK(TKIP,AES)/WPA2/WPA2-PSK(TKIP,AES)/802.1X Authentication supported
Secured Management by HTTPS
Support STP(802.1D) for wireless redundancy
Various kind of WAN Connection Type supported: Dynamic/Static IP, PPPoE, Modem/Dial Up
Support client operating mode
IP table to prevent access from unauthorized IP address
Support VPN for secured network connection (Open VPN , PPTP VPN)
Support NAT Setting (Virtual Server , Port Trigger , DMZ , UPnP)
Support DHCP forwarder through PPTP function
3G Modem signal information display (un-connecting status)
Wireless connecting status monitoring
Versatile modes & event alarm by e-mail
USB interface support 3.5G HSDPA USB Modem dial up
1KV isolation for PoE P.D. port of IAR-120+
Event Warning by Syslog, Email, SNMP Trap, Relay and Beeper
Rigid IP-30 housing design
DIN-Rail and wall mounting enabled

Specification :

IAR-120	IAR-120+
Physical Ports
10/100Base-T(X) Ports in RJ45 Auto MDI/MDIX	2
P.O.E. PD port	Present at ETH2 Fully compliant with IEEE 802.3af Power Device specifi cation Over load & short circuit protection Isolation Voltage: 1000 VDC min. Isolation Resistance : 10^8 ohms min
USB Host port	1x USB 2.0 Host port
WLAN interface
WAN Connection Type	Static/Dynamic IP / PPPoE / Modem (56K/GPRSG/3G/3.5G Modem) dial up
Antenna and connector	2dBi antenna on reverse SMA connector
Radio Frequency Type	DSSS
Modulation	IEEE802.11b : CCK, DQPSK, DBPSK IEEE802.11g : OFDM with BPSK, QPSK, 16QAM, 64QAM
Frequency Band	America/FCC : 2.412~2.462 GHz (11 channels) Europe CE/ETSI : 2.412~2.472 Ghz (13 channels)
Transmission Rate	IEEE802.11b : 1/ 2/ 5.5/ 11 Mbps IEEE802.11g : 6/ 9/ 12/ 18/ 24/ 36/ 48/ 54 Mbps
Transmit Power	IEEE802.11b/g : 18dBm
Receiver Sensitivity	-81dBm @ 11Mbps, PER< 8%; -64dBm @ 54Mbps, PER< 10%
Encryption Security	WEP : (64-bit ,128-bit key supported) WPA : WPA2 : 802.11i(WEP and AES encryption) WPAPSK (256-bit key pre-shared key supported) Radius supported TKIP encryption
Wireless Security	SSID broadcast disable
Modem Support
List	USB modems and ISDN adapters which support the Communication Device Class Abstract Control Model interface List of tested device : Hummingbird huc56s (Conexant) Huawei E220/E230 Simense HSDPA-180C Prolific 2303 + serial modem Quanta MUQ101 Sony Ericsson MD400/MD400g Sierra C885
LED Indicators
Power Indicator	PWR 1(2)(P.O.E.) / Ready : Red On : Power is on and booting up. Green On : Power is on and functioning Normally.
10/100TX RJ45 Port Indicator	Green for port Link/Act at 100Mbps. Amber for port Link/Act at 10Mbps.
WLAN LEDs	WLAN Link /ACT : Green : Link, Orange : Poor signal WLAN Strength : 1<25%, 2<50%, 3<75%, 4<100%
Fault	Red : Ethernet link down or power down
LED Indicators
Relay	Relay output to carry capacity of 1A at 24VDC
Power
Redundant Input Power	Dual DC inputs. 12-48VDC on 6-pin terminal block
Power Consumption (Typ.)	6 Watts
Overload Current Protection	Present
Reverse Polarity Protection	Present on terminal block
Physical Characteristic
Enclosure	IP-30
Dimensions (W x D x H)	52(W) x 106.1(D) x 144.3(H) mm (2.05×4.18×5.68 inch.)
Weight (g)	803 g	807 g
Environmental
Storage Temperature	-40 to 85°C (-40 to 185°F)
Operating Temperature	-10 to 70°C (14 to 158°F)
Operating Humidity	5% to 95% Non-condensing
Regulatory Approvals
EMI	FCC Part 15, CISPR (EN55022) class A
EMS	EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
Shock	IEC60068-2-27
Free Fall	IEC60068-2-32
Vibration	IEC60068-2-6
Safety	EN60950-1
Warranty	3 years

Oring IAR-120 Industrial 802.11b/g Access Point 3.5G VPN Router

Posted on June 20, 2015 by escomco

Feature :

High Speed Air Connectivity: WLAN interface support up to 54Mbps link speed
Provide HNAT enhance LAN to WAN routing performance
Highly Security Capability: WEP/WPA/WPA-PSK(TKIP,AES)/WPA2/WPA2-PSK(TKIP,AES)/802.1X Authentication supported
Secured Management by HTTPS
Support STP(802.1D) for wireless redundancy
Various kind of WAN Connection Type supported: Dynamic/Static IP, PPPoE, Modem/Dial Up
Support client operating mode
IP table to prevent access from unauthorized IP address
Support VPN for secured network connection (Open VPN , PPTP VPN)
Support NAT Setting (Virtual Server , Port Trigger , DMZ , UPnP)
Support DHCP forwarder through PPTP function
3G Modem signal information display (un-connecting status)
Wireless connecting status monitoring
Versatile modes & event alarm by e-mail
USB interface support 3.5G HSDPA USB Modem dial up
1KV isolation for PoE P.D. port of IAR-120+
Event Warning by Syslog, Email, SNMP Trap, Relay and Beeper
Rigid IP-30 housing design
DIN-Rail and wall mounting enabled

Specification :

IAR-120	IAR-120+
Physical Ports
10/100Base-T(X) Ports in RJ45 Auto MDI/MDIX	2
P.O.E. PD port	Present at ETH2 Fully compliant with IEEE 802.3af Power Device specifi cation Over load & short circuit protection Isolation Voltage: 1000 VDC min. Isolation Resistance : 10^8 ohms min
USB Host port	1x USB 2.0 Host port
WLAN interface
WAN Connection Type	Static/Dynamic IP / PPPoE / Modem (56K/GPRSG/3G/3.5G Modem) dial up
Antenna and connector	2dBi antenna on reverse SMA connector
Radio Frequency Type	DSSS
Modulation	IEEE802.11b : CCK, DQPSK, DBPSK IEEE802.11g : OFDM with BPSK, QPSK, 16QAM, 64QAM
Frequency Band	America/FCC : 2.412~2.462 GHz (11 channels) Europe CE/ETSI : 2.412~2.472 Ghz (13 channels)
Transmission Rate	IEEE802.11b : 1/ 2/ 5.5/ 11 Mbps IEEE802.11g : 6/ 9/ 12/ 18/ 24/ 36/ 48/ 54 Mbps
Transmit Power	IEEE802.11b/g : 18dBm
Receiver Sensitivity	-81dBm @ 11Mbps, PER< 8%; -64dBm @ 54Mbps, PER< 10%
Encryption Security	WEP : (64-bit ,128-bit key supported) WPA : WPA2 : 802.11i(WEP and AES encryption) WPAPSK (256-bit key pre-shared key supported) Radius supported TKIP encryption
Wireless Security	SSID broadcast disable
Modem Support
List	USB modems and ISDN adapters which support the Communication Device Class Abstract Control Model interface List of tested device : Hummingbird huc56s (Conexant) Huawei E220/E230 Simense HSDPA-180C Prolific 2303 + serial modem Quanta MUQ101 Sony Ericsson MD400/MD400g Sierra C885
LED Indicators
Power Indicator	PWR 1(2)(P.O.E.) / Ready : Red On : Power is on and booting up. Green On : Power is on and functioning Normally.
10/100TX RJ45 Port Indicator	Green for port Link/Act at 100Mbps. Amber for port Link/Act at 10Mbps.
WLAN LEDs	WLAN Link /ACT : Green : Link, Orange : Poor signal WLAN Strength : 1<25%, 2<50%, 3<75%, 4<100%
Fault	Red : Ethernet link down or power down
LED Indicators
Relay	Relay output to carry capacity of 1A at 24VDC
Power
Redundant Input Power	Dual DC inputs. 12-48VDC on 6-pin terminal block
Power Consumption (Typ.)	6 Watts
Overload Current Protection	Present
Reverse Polarity Protection	Present on terminal block
Physical Characteristic
Enclosure	IP-30
Dimensions (W x D x H)	52(W) x 106.1(D) x 144.3(H) mm (2.05×4.18×5.68 inch.)
Weight (g)	803 g	807 g
Environmental
Storage Temperature	-40 to 85°C (-40 to 185°F)
Operating Temperature	-10 to 70°C (14 to 158°F)
Operating Humidity	5% to 95% Non-condensing
Regulatory Approvals
EMI	FCC Part 15, CISPR (EN55022) class A
EMS	EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
Shock	IEC60068-2-27
Free Fall	IEC60068-2-32
Vibration	IEC60068-2-6
Safety	EN60950-1
Warranty	3 years

Oring IAP-6701N-WG+ Industrial outdoor IEEE 802.11 b/g wireless access point with 1×10 /100Base-T(X) PoE P.D., IP-67 grade, N-type antenna connector * Antenna is optional accessories

Posted on June 20, 2015 by escomco

IAP-6701N-WG+ is a reliable IP-67 outdoor IEEE 802.11 b/g WLAN Access Point with 1 PoE P.D. Ethernet port. It can be configured to operate in AP/Bridge/Repeater/AP-Client/Client mode. It is specifically designed for the toughest industrial environments. In combination with its IP-67 design and the superb management functionality. IAP-6701N-WG+ provide a waterproof, and dust-tight connection. And IAP-6701N-WG+ provide one N-type connector, that can install any N-type antenna to extended communication distance. You are able to configure IAP-6701N-WG+ by WEB interface via LAN port or WLAN interface. In addition, IAP-6701NWG+ also provides P.D. feature which is fully compliant with IEEE802.3af PoE P.D. specification to save the layout cost of power line. The IAP-6701NWG+ can be easily adopted in almost all kinds of applications and provides the most rugged solutions for managing your network in outdoor. Therefore, IAP-6701N-WG+ is one of the best outdoor communication solutions for wireless applications.

Feature :

WLAN interface supports up to 54Mbps link speed
Various kinds of operation modes supported : AP/Bridge/Repeater/ AP-Client/Client mode
Various kinds of encryption supported : WEP/WPA/WPA-PSK(TKIP,AES) /WPA2/ WPA2-PSK (TKIP,AES) /802.1X Authentication
Supports X-Roaming < 100 ms
Supports external N-type antenna install
Supports wireless load balance
Wireless connecting status monitoring
Versatile modes & event alarm by e-mail
HTTPs & SSH protocol supported for secured management
IP table to prevent access from unauthorized IP address
Event Warning by Syslog, Email, SNMP Trap
IP Configurable by Windows utility (AP-Tool)

Specification :

ORing Media Converter Model	IAP-6701N-WG+
Physical Ports
10/100 Base-T(X) Ports in RJ45 Auto MDI/MDIX with PoE P.D.	Fully compliant with IEEE 802.3af Power Device specification Over load and short circuit protection Isolation Voltage : 1000 VDC min Isolation Resistance : 10⁸ ohms min
WLAN interface
Operating Mode	AP/Bridge/Repeater/AP-Client/Client
Antenna	Built-in 12dBi panel antenna(with option to install an external N-type antenna to extend communication distance)
Radio Frequency Type	DSSS,OFDM
Modulation	IEEE802.11b : CCK, DQPSK, DBPSK IEEE802.11g : OFDM with BPSK, QPSK, 16QAM, 64QAM
Frequency Band	America/FCC : 2.412~2.462 GHz (11channels) Europe CE/ETSI : 2.412~2.472 Ghz (13 channels)
Transmission Rate	IEEE802.11b : 1/ 2/ 5.5/ 11 Mbps IEEE802.11g : 6/ 9/ 12/ 18/ 24/ 36/ 48/ 54 Mbps
Transmit Power	IEEE802.11b : 18dBm IEEE802.11g : 14dBm
Receiver Sensitivity	-80dBm @ 11Mbps, PER< 8%; -65dBm @ 54Mbps, PER< 10%
Encryption Security	WEP : (64-bit ,128-bit key supported) WPA /WPA2 : IEEE802.11i(WEP and AES encryption) WPA-PSK (256-bit key pre-shared key supported) 802.1X Authentication supported TKIP encryption
Wireless Security	SSID broadcast disable
Protocol Support
Protocol	ARP, BOOTP, DHCP, DNS, HTTPs, IP, ICMP, SNTP, TCP, UDP, RADIUS, SNMP, STP (IEEE 802.1D)
Power
Input Power	48 VDC from PoE
Power Consumption (Typ.)	6 Watts
Physical Characteristics
Enclosure	IP-67
Dimensions (W x D x H)	197.5(W) x 63(D) x 197.5(H) mm (7.80×6.34×7.80 inch.)
Weight (g)	1040g
Environmental
Storage Temperature	-40 to 85°C (-40 to 185°F)
Operating Temperature	-20 to 70°C (-4 to 158°F)
Operating Humidity	0~100% Non-condensing
Regulatory Approvals
EMI	FCC Part 15, CISPR (EN55022) class A,
EMS	EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
Shock	IEC60068-2-27
Free Fall	IEC60068-2-32
Vibration	IEC60068-2-6
Safety	EN60950-1
Warranty	3 years

Oring IAP-6701-WG+ Industrial outdoor IEEE 802.11 b/g wireless access point with 1×10/100Base-T(X) PoE P.D., IP-67 grade

Posted on June 20, 2015 by escomco

IAP-6701-WG+ is a reliable IP-67 outdoor IEEE802.11b/g WLAN Access Point with 1 PoE P.D. Ethernet port. It can be configured to operate in AP/ Bridge/Repeater/AP-Client/Client mode. It is specifically designed for the toughest industrial environments. In combination with its IP-67 design and the superb management functionality, IAP-6701-WG+ provide a waterproof, and dust-tight connection. You are able to configure IAP-6701-WG+ by WEB interface via LAN port or WLAN interface. In addition, IAP-6701-WG+ also provides P.D. feature which is fully compliant with IEEE802.3af PoE P.D. specification to save the layout cost of power line. The IAP-6701-WG+ can be easily adopted in all kinds of applications and provides the most rugged solutions for managing your network in outdoor. Therefore, IAP-6701-WG+ is one of the best communication solutions for outdoor wireless applications.

Feature :

WLAN interface supports up to 54Mbps link speed
Various kinds of operation modes supported : AP/Bridge/Repeater/ AP-Client/Client mode
Various kinds of encryption supported : WEP/WPA/WPA-PSK(TKIP,AES) /WPA2/ WPA2-PSK (TKIP,AES)/802.1X Authentication
Supports X-Roaming < 100 ms
Supports wireless load balance
Wireless connecting status monitoring
Versatile modes & event alarm by e-mail
HTTPs & SSH protocol supported for secured management
IP table to prevent access from unauthorized IP address
IP Configurable by Windows utility (AP-Tool)

Specification :

ORing Media Converter Model	IAP-6701-WG+
Physical Ports
10/100 Base-T(X) Ports in RJ45 Auto MDI/MDIX with PoE P.D.	Fully compliant with IEEE 802.3af Power Device specification Over load and short circuit protection Isolation Voltage : 1000 VDC min Isolation Resistance : 10⁸ ohms min
WLAN interface
Operating Mode	AP/Bridge/Repeater/AP-Client/Client
Antenna	Built-in 12dBi panel antenna
Radio Frequency Type	DSSS,OFDM
Modulation	IEEE802.11b : CCK, DQPSK, DBPSK IEEE802.11g : OFDM with BPSK, QPSK, 16QAM, 64QAM
Frequency Band	America/FCC : 2.412~2.462 GHz (11channels) Europe CE/ETSI : 2.412~2.472 Ghz (13 channels)
Transmission Rate	IEEE802.11b : 1/ 2/ 5.5/ 11 Mbps IEEE802.11g : 6/ 9/ 12/ 18/ 24/ 36/ 48/ 54 Mbps
Transmit Power	IEEE802.11b : 18dBm IEEE802.11g : 14dBm
Receiver Sensitivity	-80dBm @ 11Mbps, PER< 8%; -65dBm @ 54Mbps, PER< 10%
Encryption Security	WEP : (64-bit ,128-bit key supported) WPA /WPA2 : IEEE802.11i(WEP and AES encryption) WPA-PSK (256-bit key pre-shared key supported) 802.1X Authentication supported TKIP encryption
Wireless Security	SSID broadcast disable
Protocol Support
Protocol	ARP, BOOTP, DHCP, DNS, HTTPs, IP, ICMP, SNTP, TCP, UDP, RADIUS, SNMP, STP (IEEE 802.1D)
Power
Input Power	48 VDC from PoE
Power Consumption (Typ.)	6 Watts
Physical Characteristics
Enclosure	IP-67
Dimensions (W x D x H)	197.5(W) x 63(D) x 197.5(H) mm (7.80×6.34×7.80 inch.)
Weight (g)	1040g
Environmental
Storage Temperature	-40 to 85°C (-40 to 185°F)
Operating Temperature	-20 to 70°C (-4 to 158°F)
Operating Humidity	0~100% Non-condensing
Regulatory Approvals
EMI	FCC Part 15, CISPR (EN55022) class A,
EMS	EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
Shock	IEC60068-2-27
Free Fall	IEC60068-2-32
Vibration	IEC60068-2-6
Safety	EN60950-1
Warranty	3 years

Oring IGAP-6620+ Industrial Dual RF in IEEE 802.11 a/b/g/n Wireless Access Point with 2×10/100/1000Base-T(X)

Posted on June 20, 2015 by escomco

IGAP-6620+ is a reliable WLAN Access Point with 2 Ethernet Gigabit ports and dual RF in IEEE 802.11 a/b/g/n wireless modules. It can be configured to operate in AP/Bridge/Repeater/AP-Client mode. You are able to configure IGAP-6620+ by WEB interface via LAN port or WLAN interface. IGAP-6620+ provides dual Ethernet ports in switch mode, so that you can use Daisy Chain to reduce the usage of Ethernet switch ports. In addition, IGAP-6620+ also provides P.D. feature on ETH2 which is fully compliant with IEEE802.3af PoE P.D. specification. Therefore, IGAP-6620 is one of the best communication solutions for wireless applications on the industrial network..

Feature :

High Speed Air Connectivity: WLAN interface support up to 300Mbps link speed
Highly Security Capability: WEP/WPA/WPA-PSK(TKIP,AES)/ WPA2/WPA2-PSK(TKIP,AES)/802.1X Authentication supported
Support X-Roaming < 60 ms
Dual RF for redundant wireless communication
Support wireless load balance
Support MAC Filter
Support Long Distance Air Connectivity
Provide Digital Input and Digital Output
Support AP/Bridge/Repeater/AP-Client Mode
Switch Mode Supported: Daisy Chain support to reduce usage of switch ports
Dual redundant Ethernet port support redundant mode
Wireless connecting status monitoring
Secured Management by HTTPS
Event Warning by Syslog, Email, SNMP Trap, Relay and Beeper
Rigid IP-30 housing design
DIN-Rail and Wall-mount enabled

Specification :

IGAP-6620+
Physical Ports
100/1000Base-T(X) Ports in RJ45 Auto MDI/MDIX	2
5-Pin Terminal Block	4(DI and DO)
Antenna Connector	4
P.O.E. PD port	Present at ETH2 Fully compliant with IEEE 802.3af Power Device specifi cation Over load & short circuit protection Isolation Voltage : 1000 VDC min. Isolation Resistance : 108 ohms min
WLAN interface
Operating Mode	AP/Bridge/Repeater/AP-Client
Antenna and connector	Reverse SMA Female
Radio Frequency Type	DSSS
Modulation	IEEE802.11b: CCK, DQPSK, DBPSK IEEE802.11a/g: OFDM with BPSK, QPSK, 16-QAM, 64-QAM IEEE802.11n: OFDM with BPSK, QPSK, 16-QAM, 64-QAM
Frequency Band	America/FCC: 2.412~2.462 GHz (11 channels) 5.180~5.240 GHz & 5.745~5.825 GHz (9 channels) Europe CE/ETSI: 2.412~2.472 Ghz (13 channels) 5.180~5.240 GHz (4 channels)
Transmission Rate	IEEE802.11b: 1/ 2/ 5.5/ 11 Mbps IEEE802.11a/g: 6/ 9/ 12/ 18/ 24/ 36/ 48/ 54 Mbps IEEE802.11n:up to 300Mbps
Transmit Power	802.11a: 12dBm ± 1.5dBm@54Mbps 802.11b: 17dBm ± 1.5dBm@11Mbps 802.11g: 16dBm ± 1.5dBm@54Mbps 802.11gn HT20: 15dBm ± 1.5dBm @MCS7 802.11gn HT40: 14dBm ± 1.5dBm @MCS7 802.11an HT20: 12dBm ± 1.5dBm @MCS7 802.11an HT40: 11dBm ± 1.5dBm @MCS7
Receiver Sensitivity	802.11a : -76dBm ± 2dBm@54Mbps 802.11b : -85dBm ± 2dBm@11Mbps 802.11g : -76dBm ± 2dBm@54Mbps 802.11gn HT20:-75dBm ± 2dBm@MCS7 802.11gn HT40:-72dBm ± 2dBm@MCS7 802.11an HT20:-74dBm ± 2dBm@MCS7 802.11an HT40:-71dBm ± 2dBm@MCS7
Encryption Security	WEP: (64-bit ,128-bit key) WPA/WPA2 PSK :TKIP and AES encryption (802.11i) 802.1X/RADIUS Authentication supported
Wireless Security	SSID broadcast disable
Protocol Support
Protocol	ARP, BOOTP, DHCP, DNS, HTTPs, IP, ICMP, SNTP, TCP, UDP, RADIUS, SNMP, STP (IEEE 802.1D)
LED Indicators
Power Indicator	3 x LEDs, PWR1(2)(PoE) / Ready: Red On : Power is on and booting up Green On : Power is on and functioning Normal
100/1000TX RJ45 Port Indicator	2 x LEDs, LNK/ACT:Green for port Act. Speed: Green for port Link at 1000Mbps Amber for port Link at 100Mbps. Off for port Link at 10Mbps
WLAN LEDs	2 x Green Solid On: RF on, Blink: data transmitting 2 x Green for WLAN work on 2.4GHz 2 x Green for WLAN work on 5GHz
Fault	1 x LED, Red for Ethernet link down or power down indicator
Fault contact
Relay	Relay output to carry capacity of 1A at 24VDC
Power
Redundant Input Power	Dual DC inputs. 12-48VDC on 6-pin terminal block
Power Consumption (Typ.)	11
Overload Current Protection	Present
Reverse Polarity Protection	Present
Physical Characteristic
Enclosure	IP-30
Dimension (W x D x H)	74.3(W) x 109.2(D) x 153.6(H) mm (2.93 x 4.3 x 6.05 inch.)
Weight (g)	1250
Environmental
Storage Temperature	-40 to 85°C (-40 to 185°F)
Operating Temperature	-25 to 70°C (-13 to 158°F)
Operating Humidity	5% to 95% Non-condensing
Regulatory approvals
EMI	FCC Part 15, CISPR (EN55022) class A
EMS	EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS),EN61000-4-8, EN61000-4-11
Shock	IEC60068-2-27
Free Fall	IEC60068-2-32
Vibration	IEC60068-2-6
Safety	EN60950-1
Warranty	5 years