Author Archives: escomco

Oring TGAP-W6610+-M12 Industrial EN50155 Dual RF in IEEE 802.11 a/b/g/n AP with 1×10/100/1000Base-T(X) PoE P.D., IP-67 grade

Posted on by

Oring TGAP-W6610+-M12TGAP-W6610+ is a reliable outdoor wireless Access Point with dual RF IEEE 802.11 a/b/g/n wireless modules and 1 Ethernet Gigabit port with PoE P.D.. It can be configured to operate in AP/ Client /Bridge /AP-Client Mode and supports MAC filters for security control. TGAP-W6610+ provides a dust-tight connection and four N-Type connectors that can install any N-Type antennas to extend communication distance. It is specifically designed for the toughest industrial environments. You are able to configure TGAP-W6610+ by WEB interface via LAN port or WLAN interface. In addition, TGAP-W6610+ also provides P.D. feature that is fully compliant with IEEE802.3af PoE P.D. specification to save the layout cost of power line. TGAP-W6610+ can be easily adopted in almost all kinds of applications and provides the most rugged solutions for managing your network in outdoor. Therefore, TGAP-W6610+ is one of the best communication solutions for wireless applications.

Feature :

  • High Speed Air Connectivity: RF in IEEE 802.11 a/b/g/n WLAN interface support up to 300Mbps link speed
  • Dual RF for redundant wireless communication
  • Highly Security Capability: WEP/WPA/WPA-PSK(TKIP,AES)/ WPA2/WPA2-PSK(TKIP,AES)/802.1X Authentication supported
  • Support Long Distance Air Connectivity
  • Support Multiple-SSID to 4 SSID
  • Support X-Roaming < 60 ms
  • Support wireless load balance
  • Support external N-Type antenna installation
  • Support AP/ Client /Bridge /AP-Client Mode
  • Support MAC/IP/Port Filter
  • Wireless connecting status monitoring
  • Secured Management by HTTPS
  • 1KV isolation for PoE P.D.
  • Event Warning by Syslog, Email, SNMP Trap, and Beeper
  • Rigid IP-67 waterproof housing design

Specification :

TGAP-W6610+ TGAP-W6610+-M12
Physical Ports
10/100/1000Base-T(X)
Auto MDI/MDIX		 1(RJ45) 1(M12 8-pin A-coding)
PoE P.D. port Present at ETH
Fully compliant with IEEE 802.3af Power Device specification
Over load & short circuit protection
Isolation Voltage: 1000 VDC min.
Isolation Resistance : 108 ohms min
WLAN interface
Operating Mode Dual AP/Dual Client /Bridge /AP-Client Mode
Antenna and connector 4 x External N-Type female antenna connector
Radio Frequency Type DSSS, OFDM
Modulation IEEE802.11a : OFDM with BPSK, QPSK, QAM, 64QAM
IEEE802.11b: CCK, DQPSK, DBPSK
IEEE802.11g: OFDM with BPSK, QPSK, 16QAM, 64QAM
IEEE802.11n : BPSK, QPSK, 16-QAM, 64-QAM
Frequency Band

America / FCC :  2.412~2.462 GHz (11 channels)
5.180~5.240 GHz & 5.745~5.825 GHz ( 9 channels )
Europe CE / ETSI : 2.412~2.472 Ghz (13 channels)
5.180~5.240 GHz (4 channels)
Transmission Rate IEEE802.11b: 1 / 2 / 5.5 / 11 Mbps
IEEE802.11a/g: 6 / 9 / 12 / 18 / 24 / 36 / 48 / 54 Mbps
IEEE801.11n: up to 300Mbps
Transmit Power 802.11a: 12dBm ± 1.5dBm
802.11b: 17dBm ± 1.5dBm
802.11g: 15dBm ± 1.5dBm
802.11gn HT20: 13dBm ± 1.5dBm@150Mbps
802.11gn HT40: 12dBm ± 1.5dBm@300Mbps
802.11an HT20: 12dBm ± 1.5dBm@150Mbps
802.11an HT40: 12dBm ± 1.5dBm@300Mbps
Receiver Sensitivity 802.11a: -68dBm ±2dBm@54Mbps
802.11b: -85dBm ±2dBm@11Mbps
802.11g: -68dBm ±2dBm@54Mbps
802.11gn HT20: -68dBm ±2dBm@150Mbps
802.11gn HT40: -68dBm ±2dBm@300Mbps
802.11an HT20: -68dBm ±2dBm@150Mbps
802.11an HT40: -68dBm ±2dBm@300Mbps
Encryption Security WEP: (64-bit ,128-bit key supported)
WPA/WPA2 :802.11i(WEP and AES encryption)
WPAPSK (256-bit key pre-shared key supported)
802.1X Authentication supported
TKIP encryption
Wireless Security SSID broadcast disable and enable
Protocol Support
Protocol ARP,BOOTP, DHCP, DNS, HTTP, IP, ICMP, SNTP, TCP, UDP, RADIUS, SNMP, STP, RSTP
LED Indicators
Power Indicator 3 x LEDs, PW1/PW2/PoE Green On : Power is on and booting up
10/100/1000TX M12 Port Indicator 1 x LEDs, Green for port Link/Act
WLAN LEDs 2 x LEDs, Green for WLAN Link/Act
Fault 1 x LED, Red for Ethernet link down or power down indicator
Power
Redundant Input Power Dual Power Inputs. 12~48 VDC
Power Consumption (Typ.) 11 Watts
Physical Characteristic
Enclosure IP-67
Dimension (W x D x H) 310 (W) x 310(D) x 87 (H) (12.2 x 12.2 x 3.4 inch)
Weight (g) 3980 g
Environmental
Storage Temperature -40 to 85°C (-40 to 185°F)
Operating Temperature -25 to 70°C (-13 to 158°F)
Operating Humidity 5% to 95% Non-condensing
Regulatory approvals
EMI FCC Part 15, CISPR (EN55022) class A, EN50155 (EN50121-3-2, EN55011, EN50121-4)
EMS EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
Rail Traffic EN50155
Shock IEC60068-2-27, EN61373
Free Fall IEC60068-2-31
Rail Traffic EN50155
Vibration IEC60068-2-6, EN61373
Rail Traffic EN50155
Cooling EN60068-2-1
Dry Heat En60068-2-2
Safety EN60950-1
Warranty 5 years

Oring TGAP-W610+ Industrial EN50155 IEEE 802.11 a/b/g/n AP with 1×10/100/1000Base-T(X) PoE P.D., IP-67 gradeP.D., IP-67 grade

Posted on by

Oring TGAP-W610+TGAP-W610+ is a reliable outdoor wireless Access Point with IEEE 802.11 a/b/g/n wireless modules and 1 Ethernet Gigabit port with PoE P.D.. It can be configured to operate in AP/ Client /Bridge /AP-Client Mode and supports MAC filters for security control. TGAP-W610+ provides a dust-tight connection and four N-Type connectors that can install any N-Type antennas to extend communication distance. It is specifically designed for the toughest industrial environments. You are able to configure TGAP-W610+ by WEB interface via LAN port or WLAN interface. In addition, TGAP-W610+ also provides P.D. feature that is fully compliant with IEEE802.3af PoE P.D. specification to save the layout cost of power line. TGAP-W610+ can be easily adopted in almost all kinds of applications and provides the most rugged solutions for managing your network in outdoor. Therefore, TGAP-W610+ is one of the best communication solutions for wireless applications.

Feature :

  • High Speed Air Connectivity: WLAN interface support up to 300 Mbps link speed
  • Highly Security Capability: WEP/WPA/WPA-PSK(TKIP,AES)/ WPA2/WPA2-PSK(TKIP,AES)/802.1X Authentication supported
  • Support Long Distance Air Connectivity
  • Support Multiple-SSID to 4 SSID
  • Support X-Roaming < 60 ms
  • Support wireless load balance
  • Support external N-Type antenna installation
  • Support AP/ Client /Bridge /AP-Client Mode
  • Support MAC/IP/Port Filter
  • Wireless connecting status monitoring
  • Secured Management by HTTPS
  • 1KV isolation for PoE P.D.
  • Event Warning by Syslog, Email, SNMP Trap, and Relay output
  • Rigid IP-67 waterproof housing design

Specification :

TGAP-W610+ TGAP-W610+-M12
Physical Ports
10/100/1000Base-T(X)
Auto MDI/MDIX		 1 (RJ45) 1 (M12 8-pin A-coding)
PoE P.D. port Present at ETH
Fully compliant with IEEE 802.3af Power Device specification
Over load & short circuit protection
Isolation Voltage: 1000 VDC min.
Isolation Resistance : 108 ohms min
WLAN interface
Operating Mode P/Dual Client /Bridge /AP-Client Mode
Antenna and connector 2 x External N-Type female antenna connector
Radio Frequency Type DSSS, OFDM
Modulation IEEE802.11a : OFDM with BPSK, QPSK, QAM, 64QAM
IEEE802.11b: CCK, DQPSK, DBPSK
IEEE802.11g: OFDM with BPSK, QPSK, 16QAM, 64QAM
IEEE802.11n : BPSK, QPSK, 16-QAM, 64-QAM
Frequency Band

America / FCC :  2.412~2.462 GHz (11 channels)

5.180~5.240 GHz & 5.745~5.825 GHz ( 9 channels )

Europe CE / ETSI : 2.412~2.472 Ghz (13 channels)
5.180~5.240 GHz (4 channels)
Transmission Rate IEEE802.11b: 1 / 2 / 5.5 / 11 Mbps
IEEE802.11a/g: 6 / 9 / 12 / 18 / 24 / 36 / 48 / 54 Mbps
IEEE801.11n: up to 300Mbps
Transmit Power 802.11a: 12dBm ± 1.5dBm
802.11b: 17dBm ± 1.5dBm
802.11g: 15dBm ± 1.5dBm
802.11gn HT20: 13dBm ± 1.5dBm@150Mbps
802.11gn HT40: 12dBm ± 1.5dBm@300Mbps
802.11an HT20: 12dBm ± 1.5dBm@150Mbps
802.11an HT40: 12dBm ± 1.5dBm@300Mbps
Receiver Sensitivity 802.11a: -68dBm ±2dBm@54Mbps
802.11b: -85dBm ±2dBm@11Mbps
802.11g: -68dBm ±2dBm@54Mbps
802.11gn HT20: -68dBm ±2dBm@150Mbps
802.11gn HT40: -68dBm ±2dBm@300Mbps
802.11an HT20: -68dBm ±2dBm@150Mbps
802.11an HT40: -68dBm ±2dBm@300Mbps
Encryption Security WEP: (64-bit ,128-bit key supported)
WPA/WPA2 :802.11i(WEP and AES encryption)
WPAPSK (256-bit key pre-shared key supported)
802.1X Authentication supported
TKIP encryption
Wireless Security SSID broadcast disable and enable
Protocol Support
Protocol ARP,BOOTP, DHCP, DNS, HTTP, IP, ICMP, SNTP, TCP, UDP, RADIUS, SNMP, STP, RSTP
LED Indicators
Power Indicator 3 x LEDs, PW1/PW2/PoE Green On : Power is on
10/100/1000TX M12 Port Indicator 1 x LEDs, Green for port Link/Act
WLAN LED 1 x LEDs, Green for WLAN Link /Act
Fault
Power Dual Power Inputs. 12~48 VDC
Input power
Redundant Input Power
Power Consumption (Typ.) 9Watt
Physical Characteristic
Enclosure IP-67
Dimension (W x D x H) 310 (W) x 310(D) x 87 (H) (12.2 x 12.2 x 3.4 inch)
Weight (g) 3900g
Environmental
Storage Temperature -40 to 85°C (-40 to 185°F)
Operating Temperature -25 to 70°C (-13 to 158°F)
Operating Humidity 5% to 95% Non-condensing
Regulatory approvals
EMI FCC Part 15, CISPR (EN55022) class A, EN50155 (EN50121-3-2)
EMS EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
Shock IEC60068-2-27, EN61373
Free Fall IEC60068-2-31
Vibration IEC60068-2-6, EN61373
Rail Traffic EN50155
Cooling EN60068-2-1
Dry Heat En60068-2-2
Safety EN60950-1
Warranty 5 years

Oring TGAP-6620-M12 Industrial EN50155 Dual RF in IEEE 802.11 a/b/g/n Wireless AP with 2×10/100/1000Base-T(X), M12 connector

Posted on by

Oring TGAP-6620-M12TGAP-6620-M12 is a reliable WLAN Access Point with 2 Ethernet Gigabit ports and dual RF in IEEE 802.11 a/b/g/n wireless modules. It can be configured to operate in Dual AP/Dual Client /Bridge /AP-Client Mode. In combination with its IP-40 design and the superb management functionality, TGAP-6620-M12 provides a dust-tight connection and reverse SMA-type connectors, that can install any reverse SMA-type antennas to extend communication distance. It is specifically designed for the toughest industrial environments. You are able to configure TGAP-6620-M12 by WEB interface via LAN port or WLAN interface. TGAP-6620-M12 can be easily adopted in almost all kinds of applications and provides the most rugged solutions for managing your network in outdoor. In addition, TGAP-6620+-M12 also provides P.D. feature on ETH2 which is fully compliant with IEEE802.3af PoE P.D. specification. Therefore, TGAP-6620-M12 is one of the best communication solutions for wireless applications.

Feature :

  • High Speed Air Connectivity: WLAN interface support up to 300 Mbps link speed
  • Highly Security Capability: WEP/WPA/WPA-PSK(TKIP,AES)/ WPA2/WPA2-PSK(TKIP,AES)/802.1X Authentication supported
  • Dual Gigabit Ethernet ports support Ethernet redundant mode (Recovery time < 10ms) and switch mode in M12 connector (A-coding)
  • Support X-Roaming < 60 ms
  • Support wireless load balance
  • Support Multiple-SSID to 4 SSID
  • Support external SMA antenna installation
  • Support dual AP/Dual Client /Bridge /AP-Client Mode
  • Support MAC Filter
  • Wireless connecting status monitoring
  • 1KV isolation for PoE P.D. port for TGAP-6620+-M12 • Secured Management by HTTPS
  • Event Warning by Syslog, Email, SNMP Trap, and Relay output
  • Rigid IP-40 housing design
  • Wall-mount enabled

Specification :

TGAP-6620-M12 TGAP-6620+-M12
Physical Ports
100/1000Base-T(X) Ports in M12 Auto MDI/MDIX (8-pin A-coding) 2 2 (Present at ETH2 Fully Compiant with IEEE 802.3af PoE P.D.)
DIDO port in M12 (A-Coding) 2(DI x 4 and DO x 4)
Dry Contact:
On: short to GND, off: open
Wet Contact(DI to COM/GND):
On: 0 to 3VDC, off: 10 to 30VDC
RS-232 Console port in M12 (5-pin A-coding) 115200, 8 ,N ,1
Antenna Connector 4
 Relay port in M12 (5-pin A-coding)  1A@24VDC
WLAN interface
Operating Mode AP/Bridge/Repeater/AP-Client
Antenna and connector 4 x Reverse SMA Female
Radio Frequency Type DSSS
Modulation IEEE802.11b: CCK, DQPSK, DBPSK
IEEE802.11a/g: OFDM with BPSK, QPSK, 16-QAM, 64-QAM
IEEE802.11n: OFDM with BPSK, QPSK, 16-QAM, 64-QAM
Frequency Band

America/FCC: 2.412~2.462 GHz (11 channels)
5.180~5.240 GHz & 5.745~5.825 GHz (9 channels)
Europe CE/ETSI: 2.412~2.472 Ghz (13 channels)
5.180~5.240 GHz  (4 channels)

Transmission Rate IEEE802.11b: 1 / 2 / 5.5 / 11 Mbps
IEEE802.11a/g: 6 / 9 / 12 / 18 / 24 / 36 / 48 / 54 Mbps
IEEE801.11n: up to 300Mbps
Transmit Power 802.11a: 12dBm ± 1.5dBm
802.11b: 18dBm ± 1.5dBm
802.11g: 15dBm ± 1.5dBm
802.11gn HT20: 13dBm ± 1.5dBm@150Mbps
802.11gn HT40: 12dBm ± 1.5dBm@300Mbps
802.11an HT20: 12dBm ± 1.5dBm@150Mbps
802.11an HT40: 12dBm ± 1.5dBm@300Mbps
Receiver Sensitivity 802.11a: -68dBm ±2dBm@54Mbps
802.11b: -85dBm ±2dBm@11Mbps
802.11g: -68dBm ±2dBm@54Mbps
802.11gn HT20: -68dBm ±2dBm@150Mbps
802.11gn HT40: -68dBm ±2dBm@300Mbps
802.11an HT20: -68dBm ±2dBm@150Mbps
802.11an HT40: -68dBm ±2dBm@300Mbps
Encryption Security WEP: (64-bit ,128-bit key supported)
WPA/WPA2 :802.11i(WEP and AES encryption)
WPAPSK (256-bit key pre-shared key supported)
802.1X Authentication supported
TKIP encryption
Wireless Security SSID broadcast disable and enable
Protocol Support
Protocol ARP,BOOTP, DHCP, DNS, HTTP, IP, ICMP, SNTP, TCP, UDP, RADIUS, SNMP, STP, RSTP
LED Indicators
Power Indicator 2 x LEDs, Green for Power on
10/100/1000TX RJ45 Port Indicator 2 x LEDs, Green for port Link/Act
WLAN LED 2 x LEDs, Green for WLAN Link/Act
Fault 1 x LED, Red for Ethernet link down or power down indicator
Fault contact
Relay Relay output to carry capacity of 1A at 24VDC(5-pin M12 A-coding)
Power
Redundant Input Power Dual Power Inputs. 12~48 VDC
Power Consumption (Typ.) 11 Watts 11.5 Watts
Physical Characteristic
Enclosure IP-40
Dimension (W x D x H) 125.6(W) x 65(D) x 196.1(H) mm (4.94 x 2.55 x 7.72 inch.)
Weight (g) 980 g 985 g
Environmental
Storage Temperature -40 to 85°C (-40 to 185°F)
Operating Temperature -25 to 70°C (-13 to 158°F)
Operating Humidity 5% to 95% Non-condensing
Regulatory approvals
EMI FCC Part 15, CISPR (EN55022) class A, EN50155 (EN50121-3-2, EN55011, EN50121-4)
EMS EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
Shock IEC60068-2-27, EN61373
Free Fall IEC60068-2-31
Vibration IEC60068-2-6, EN61373
Safety EN60950-1
Warranty 5 years

Oring TGAP-620+-M12 Industrial EN50155 IEEE 802.11 a/b/g/n wireless access point with 2×10/100/1000Base-T(X), M12 connector

Posted on by

Oring TGAP-620+-M12ORing’s TransporterTM series access point is designed for industrial and rolling stock wireless applications, such as vehicle, and railway applications. TGAP-620-M12 is a reliable 802.11 a/b/g/n WLAN Access Point with 2 Ethernet 10/100/1000 ports. It can be configured to operate in AP/Client /Bridge /AP-Client Mode. TGAP-620-M12 provides dual Ethernet ports in switch mode, so that you can use Daisy Chain to reduce the usage of Ethernet switch ports. TGAP-620-M12 provides a dust-tight connection and reverses SMA-type connectors that can install any reverse SMA-type antennas to extend communication distance. It is specifically designed for the toughest industrial environments. You are able to configure TGAP-620-M12 by WEB interface via LAN port or WLAN interface. TGAP-620-M12 can be easily adopted in almost all kinds of applications and provides the most rugged solutions for managing your network in outdoor. In addition, TGAP-620+-M12 also provides P.D. feature on ETH2 which is fully compliant with IEEE802.3af PoE P.D. specification. Therefore, TGAP-620-M12 is one of the best communication solutions for wireless applications.

Feature :

  • High Speed Air Connectivity: WLAN interface support up to 300 Mbps link speed
  • Highly Security Capability: WEP/WPA/WPA-PSK(TKIP,AES)/ WPA2/WPA2-PSK(TKIP,AES)/802.1X Authentication supported
  • Dual Gigabit Ethernet ports support Ethernet redundant mode (Recovery time < 10ms) and switch mode in M12 connector (A-coding)
  • Support X-Roaming < 60 ms
  • Support wireless load balance
  • Support Multiple-SSID to 4 SSID
  • Support external SMA antenna installation
  • Support AP/Client /Bridge /AP-Client Mode
  • Support MAC Filter
  • Dual Ethernet ports support Ethernet redundant mode (Recovery time < 10ms) and switch mode in M12 connector (A-coding)
  • Wireless connecting status monitoring
  • 1KV isolation for PoE P.D. port for TGAP-620+-M12 • Secured Management by HTTPS
  • Event Warning by Syslog, Email, SNMP Trap, and Relay output
  • Rigid IP-40 housing design
  • Wall-mount enabled

Specification :

TGAP-620-M12 TGAP-620+-M12
Physical Ports
100/1000Base-T(X) Ports in M12 Auto MDI/MDIX (8-pin A-coding) 2 2 (Present at ETH2 Fully Compiant with IEEE 802.3af PoE P.D.)
DIDO port in M12 (A-Coding) 2(DI x 4 and DO x 4)
Dry Contact:
On: short to GND, off: open
Wet Contact(DI to COM/GND):
On: 0 to 3VDC, off: 10 to 30VDC
RS-232 Console port in M12 (5-pin A-coding) 115200, 8 ,N ,1
Antenna Connector 2
 Relay port in M12 (5-pin A-coding)  1A@24VDC
WLAN interface
Operating Mode AP/Bridge/Repeater/AP-Client
Antenna and connector 2 x Reverse SMA Female
Radio Frequency Type DSSS
Modulation IEEE802.11b: CCK, DQPSK, DBPSK
IEEE802.11a/g: OFDM with BPSK, QPSK, 16-QAM, 64-QAM
IEEE802.11n: OFDM with BPSK, QPSK, 16-QAM, 64-QAM
Frequency Band

America/FCC: 2.412~2.462 GHz (11 channels)
5.180~5.240 GHz & 5.745~5.825 GHz (9 channels)
Europe CE/ETSI: 2.412~2.472 Ghz (13 channels)
5.180~5.240 GHz  (4 channels)
Transmission Rate IEEE802.11b: 1 / 2 / 5.5 / 11 Mbps
IEEE802.11a/g: 6 / 9 / 12 / 18 / 24 / 36 / 48 / 54 Mbps
IEEE801.11n: up to 300Mbps
Transmit Power 802.11a: 12dBm ± 1.5dBm
802.11b: 18dBm ± 1.5dBm
802.11g: 15dBm ± 1.5dBm
802.11gn HT20: 13dBm ± 1.5dBm@150Mbps
802.11gn HT40: 12dBm ± 1.5dBm@300Mbps
802.11an HT20: 12dBm ± 1.5dBm@150Mbps
802.11an HT40: 12dBm ± 1.5dBm@300Mbps
Receiver Sensitivity 802.11a: -68dBm ±2dBm@54Mbps
802.11b: -85dBm ±2dBm@11Mbps
802.11g: -68dBm ±2dBm@54Mbps
802.11gn HT20: -68dBm ±2dBm@150Mbps
802.11gn HT40: -68dBm ±2dBm@300Mbps
802.11an HT20: -68dBm ±2dBm@150Mbps
802.11an HT40: -68dBm ±2dBm@300Mbps
Encryption Security WEP: (64-bit ,128-bit key supported)
WPA/WPA2 :802.11i(WEP and AES encryption)
WPAPSK (256-bit key pre-shared key supported)
802.1X Authentication supported
TKIP encryption
Wireless Security SSID broadcast disable and enable
Protocol Support
Protocol ARP,BOOTP, DHCP, DNS, HTTP, IP, ICMP, SNTP, TCP, UDP, RADIUS, SNMP, STP, RSTP
LED Indicators
Power Indicator 2 x LEDs, Green for Power on
10/100/1000TX RJ45 Port Indicator 2 x LEDs, Green for port Link/Act
WLAN LED 1 x LED, Green for WLAN Link/Act
Fault 1 x LED, Red for Ethernet link down or power down indicator
Fault contact
Relay Relay output to carry capacity of 1A at 24VDC(5-pin M12 A-coding)
Power
Redundant Input Power Dual Power Inputs. 12~48 VDC
Power Consumption (Typ.) 7 Watts 7.5 Watts
Physical Characteristic
Enclosure IP-40
Dimension (W x D x H) 125.6(W) x 65(D) x 196.1(H) mm (4.94 x 2.55 x 7.72 inch.)
Weight (g) 965 g 970 g
Environmental
Storage Temperature -40 to 85°C (-40 to 185°F)
Operating Temperature -25 to 70°C (-13 to 158°F)
Operating Humidity 5% to 95% Non-condensing
Regulatory approvals
EMI FCC Part 15, CISPR (EN55022) class A, EN50155 (EN50121-3-2, EN55011, EN50121-4)
EMS EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
Shock IEC60068-2-27, EN61373
Free Fall IEC60068-2-31
Vibration IEC60068-2-6, EN61373
Safety EN60950-1
Warranty 5 years