Author Archives: escomco

Oring IGAP-620+ Industrial IEEE 802.11 a/b/g/n wireless access point with 2×10/100/1000 Base-T(X)

Posted on by

Oring IGAP-620+IGAP-620 is a reliable WLAN Access Point with 2 Ethernet Gigabit ports and IEEE 802.11 a/b/g/n wireless modules. It can be configured to operate in AP/Bridge/Repeater/AP-Client mode. You are able to configure IGAP-620 by WEB interface via LAN port or WLAN interface. IGAP-620 provides dual Ethernet ports in switch mode, so that you can use Daisy Chain to reduce the usage of Ethernet switch ports. In addition, IGAP-620 series also provides P.D. feature on ETH2 which is fully compliant with IEEE802.3af PoE P.D. specification. Therefore, IGAP-620 is one of the best communication solutions for wireless applications on the industrial network..

Feature :

  • High Speed Air Connectivity: WLAN interface support up to 300Mbps link speed
  • Highly Security Capability: WEP/WPA/WPA-PSK(TKIP,AES)/ WPA2/WPA2-PSK(TKIP,AES)/802.1X Authentication supported
  • Support X-Roaming < 60 ms
  • Support wireless load balance
  • Support MAC Filter
  • Support Long Distance Air Connectivity
  • Provide Digital Input and Digital Output
  • Support AP/Bridge/Repeater/AP-Client Mode
  • Switch Mode Supported: Daisy Chain support to reduce usage of switch ports
  • Dual redundant Ethernet port support redundant mode
  • Wireless connecting status monitoring
  • Secured Management by HTTPS
  • Event Warning by Syslog, Email, SNMP Trap, Relay and Beeper
  • Rigid IP-30 housing design
  • DIN-Rail and Wall-mount enabled

Specification :

IGAP-620 IGAP-620+
Physical Ports
100/1000Base-T(X) Ports in RJ45 Auto MDI/MDIX                                                                                     2
5-Pin Terminal Block 4(DI and DO)
Antenna Connector 2
P.O.E. PD port Present at ETH2
Fully compliant with IEEE 802.3af  Power Device specifi cation
Over load & short circuit protection
Isolation Voltage : 1000 VDC min.
Isolation Resistance : 108 ohms min
WLAN interface
Operating Mode AP/Bridge/Repeater/AP-Client
Antenna and connector Reverse SMA Female
Radio Frequency Type DSSS
Modulation IEEE802.11b: CCK, DQPSK, DBPSK
IEEE802.11a/g: OFDM with BPSK, QPSK, 16-QAM, 64-QAM
IEEE802.11n: OFDM with BPSK, QPSK, 16-QAM, 64-QAM
Frequency Band

America/FCC: 2.412~2.462 GHz (11 channels)
5.180~5.240 GHz & 5.745~5.825 GHz (9 channels)
Europe CE/ETSI: 2.412~2.472 Ghz (13 channels)
5.180~5.240 GHz  (4 channels)

Transmission Rate IEEE802.11b: 1/ 2/ 5.5/ 11 Mbps
IEEE802.11a/g: 6/ 9/ 12/ 18/ 24/ 36/ 48/ 54 Mbps
IEEE802.11n:up to 300Mbps
Transmit Power 802.11a: 12dBm ± 1.5dBm@54Mbps
802.11b: 17dBm ± 1.5dBm@11Mbps
802.11g: 16dBm ± 1.5dBm@54Mbps
802.11gn HT20: 15dBm ± 1.5dBm @MCS7
802.11gn HT40: 14dBm ± 1.5dBm @MCS7
802.11an HT20: 12dBm ± 1.5dBm @MCS7
802.11an HT40: 11dBm ± 1.5dBm @MCS7
Receiver Sensitivity 802.11a : -76dBm ± 2dBm@54Mbps
802.11b : -85dBm ± 2dBm@11Mbps
802.11g : -76dBm ± 2dBm@54Mbps
802.11gn HT20:-75dBm ± 2dBm@MCS7
802.11gn HT40:-72dBm ± 2dBm@MCS7
802.11an HT20:-74dBm ± 2dBm@MCS7
802.11an HT40:-71dBm ± 2dBm@MCS7
Encryption Security WEP: (64-bit ,128-bit key)
WPA/WPA2 PSK :TKIP and AES encryption (802.11i)
802.1X/RADIUS Authentication supported
Wireless Security SSID broadcast disable
Protocol Support
Protocol ARP, BOOTP, DHCP, DNS, HTTPs, IP, ICMP, SNTP, TCP, UDP, RADIUS, SNMP, STP (IEEE 802.1D)
LED Indicators
Power Indicator 3 x LEDs, PWR1(2)(PoE) / Ready:
Red On : Power is on and booting up
Green On : Power is on and functioning Normal
100/1000TX RJ45 Port Indicator 2 x LEDs,
LNK/ACT:Green for port Act.
Speed: Green for port Link at 1000Mbps
Amber for port Link at 100Mbps.
Off for port Link at 10Mbps
WLAN LEDs 1 x LED, Green for WLAN Link/ Act
Fault 1 x LED, Red for Ethernet link down or power down indicator
Fault contact
Relay Relay output to carry capacity of 1A at 24VDC
Power
Redundant Input Power Dual DC inputs. 12-48VDC on 6-pin terminal block Dual DC inputs. 12-48VDC on 6-pin terminal block
Power Consumption (Typ.) 7.5W 8.5W
Overload Current Protection Present
Reverse Polarity Protection Present
Physical Characteristic
Enclosure IP-30
Dimension (W x D x H) 74.3(W) x 109.2(D) x 153.6(H) mm (2.93 x 4.3 x 6.05 inch.)
Weight (g) 1150 1155
Environmental
Storage Temperature -40 to 85°C (-40 to 185°F)
Operating Temperature -25 to 70°C (-13 to 158°F)
Operating Humidity 5% to 95% Non-condensing
Regulatory approvals
EMI FCC Part 15, CISPR (EN55022) class A
EMS EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS),EN61000-4-8, EN61000-4-11
Shock IEC60068-2-27
Free Fall IEC60068-2-32
Vibration IEC60068-2-6
Safety EN60950-1
Warranty 5 years

Oring IGAP-620 Industrial IEEE 802.11 a/b/g/n wireless access point with 2×10/100/1000 Base-T(X)

Posted on by

Oring IGAP-620IGAP-620 is a reliable WLAN Access Point with 2 Ethernet Gigabit ports and IEEE 802.11 a/b/g/n wireless modules. It can be configured to operate in AP/Bridge/Repeater/AP-Client mode. You are able to configure IGAP-620 by WEB interface via LAN port or WLAN interface. IGAP-620 provides dual Ethernet ports in switch mode, so that you can use Daisy Chain to reduce the usage of Ethernet switch ports. In addition, IGAP-620 series also provides P.D. feature on ETH2 which is fully compliant with IEEE802.3af PoE P.D. specification. Therefore, IGAP-620 is one of the best communication solutions for wireless applications on the industrial network..

Feature :

  • High Speed Air Connectivity: WLAN interface support up to 300Mbps link speed
  • Highly Security Capability: WEP/WPA/WPA-PSK(TKIP,AES)/ WPA2/WPA2-PSK(TKIP,AES)/802.1X Authentication supported
  • Support X-Roaming < 60 ms
  • Support wireless load balance
  • Support MAC Filter
  • Support Long Distance Air Connectivity
  • Provide Digital Input and Digital Output
  • Support AP/Bridge/Repeater/AP-Client Mode
  • Switch Mode Supported: Daisy Chain support to reduce usage of switch ports
  • Dual redundant Ethernet port support redundant mode
  • Wireless connecting status monitoring
  • Secured Management by HTTPS
  • Event Warning by Syslog, Email, SNMP Trap, Relay and Beeper
  • Rigid IP-30 housing design
  • DIN-Rail and Wall-mount enabled

Specification :

IGAP-620 IGAP-620+
Physical Ports
100/1000Base-T(X) Ports in RJ45 Auto MDI/MDIX                                                                                     2
5-Pin Terminal Block 4(DI and DO)
Antenna Connector 2
P.O.E. PD port Present at ETH2
Fully compliant with IEEE 802.3af  Power Device specifi cation
Over load & short circuit protection
Isolation Voltage : 1000 VDC min.
Isolation Resistance : 108 ohms min
WLAN interface
Operating Mode AP/Bridge/Repeater/AP-Client
Antenna and connector Reverse SMA Female
Radio Frequency Type DSSS
Modulation IEEE802.11b: CCK, DQPSK, DBPSK
IEEE802.11a/g: OFDM with BPSK, QPSK, 16-QAM, 64-QAM
IEEE802.11n: OFDM with BPSK, QPSK, 16-QAM, 64-QAM
Frequency Band

America/FCC: 2.412~2.462 GHz (11 channels)
5.180~5.240 GHz & 5.745~5.825 GHz (9 channels)
Europe CE/ETSI: 2.412~2.472 Ghz (13 channels)
5.180~5.240 GHz  (4 channels)
Transmission Rate IEEE802.11b: 1/ 2/ 5.5/ 11 Mbps
IEEE802.11a/g: 6/ 9/ 12/ 18/ 24/ 36/ 48/ 54 Mbps
IEEE802.11n:up to 300Mbps
Transmit Power 802.11a: 12dBm ± 1.5dBm@54Mbps
802.11b: 17dBm ± 1.5dBm@11Mbps
802.11g: 16dBm ± 1.5dBm@54Mbps
802.11gn HT20: 15dBm ± 1.5dBm @MCS7
802.11gn HT40: 14dBm ± 1.5dBm @MCS7
802.11an HT20: 12dBm ± 1.5dBm @MCS7
802.11an HT40: 11dBm ± 1.5dBm @MCS7
Receiver Sensitivity 802.11a : -76dBm ± 2dBm@54Mbps
802.11b : -85dBm ± 2dBm@11Mbps
802.11g : -76dBm ± 2dBm@54Mbps
802.11gn HT20:-75dBm ± 2dBm@MCS7
802.11gn HT40:-72dBm ± 2dBm@MCS7
802.11an HT20:-74dBm ± 2dBm@MCS7
802.11an HT40:-71dBm ± 2dBm@MCS7
Encryption Security WEP: (64-bit ,128-bit key)
WPA/WPA2 PSK :TKIP and AES encryption (802.11i)
802.1X/RADIUS Authentication supported
Wireless Security SSID broadcast disable
Protocol Support
Protocol ARP, BOOTP, DHCP, DNS, HTTPs, IP, ICMP, SNTP, TCP, UDP, RADIUS, SNMP, STP (IEEE 802.1D)
LED Indicators
Power Indicator 3 x LEDs, PWR1(2)(PoE) / Ready:
Red On : Power is on and booting up
Green On : Power is on and functioning Normal
100/1000TX RJ45 Port Indicator 2 x LEDs,
LNK/ACT:Green for port Act.
Speed: Green for port Link at 1000Mbps
Amber for port Link at 100Mbps.
Off for port Link at 10Mbps
WLAN LEDs 1 x LED, Green for WLAN Link/ Act
Fault 1 x LED, Red for Ethernet link down or power down indicator
Fault contact
Relay Relay output to carry capacity of 1A at 24VDC
Power
Redundant Input Power Dual DC inputs. 12-48VDC on 6-pin terminal block Dual DC inputs. 12-48VDC on 6-pin terminal block
Power Consumption (Typ.) 7.5W 8.5W
Overload Current Protection Present
Reverse Polarity Protection Present
Physical Characteristic
Enclosure IP-30
Dimension (W x D x H) 74.3(W) x 109.2(D) x 153.6(H) mm (2.93 x 4.3 x 6.05 inch.)
Weight (g) 1150 1155
Environmental
Storage Temperature -40 to 85°C (-40 to 185°F)
Operating Temperature -25 to 70°C (-13 to 158°F)
Operating Humidity 5% to 95% Non-condensing
Regulatory approvals
EMI FCC Part 15, CISPR (EN55022) class A
EMS EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS),EN61000-4-8, EN61000-4-11
Shock IEC60068-2-27
Free Fall IEC60068-2-32
Vibration IEC60068-2-6
Safety EN60950-1
Warranty 5 years

Oring IGAP-420 Industrial IEEE 802.11 b/g/n wireless access point with 2×10/100/1000 Base-T(X)

Posted on by

Oring IGAP-420IGAP-420 is a reliable WLAN Access Point with 2 Ethernet Gigabit ports and IEEE 802.11 b/g/n wireless modules. It can be configured to operate in AP/Bridge/Repeater/AP-Client mode. You are able to configure IGAP-420 by WEB interface via LAN port or WLAN interface. IGAP-420 provides dual Ethernet ports in switch mode, so that you can use Daisy Chain to reduce the usage of Ethernet switch ports. In addition, IGAP-420 series also provides P.D. feature on ETH2 which is fully compliant with IEEE802.3af PoE P.D. specification. Therefore, IGAP-420 is one of the best communication solutions for wireless applications on the industrial network..

Feature :

  • High Speed Air Connectivity: WLAN interface support up to 300Mbps link speed
  • Highly Security Capability: WEP/WPA/WPA-PSK(TKIP,AES)/ WPA2/WPA2-PSK(TKIP,AES)/802.1X Authentication supported
  • Support X-Roaming < 60 ms
  • Support wireless load balance
  • Support MAC Filter
  • Support Long Distance Air Connectivity
  • Provide Digital Input and Digital Output
  • Support AP/Bridge/Repeater/AP-Client Mode
  • Switch Mode Supported: Daisy Chain support to reduce usage of switch ports
  • Dual redundant Ethernet port support redundant mode
  • Wireless connecting status monitoring
  • Secured Management by HTTPS
  • Event Warning by Syslog, Email, SNMP Trap, Relay and Beeper
  • Rigid IP-30 housing design
  • DIN-Rail and Wall-mount enabled

Specification :

IGAP-420 IGAP-420+
Physical Ports
100/1000Base-T(X) Ports in RJ45 Auto MDI/MDIX                                                                                     2
5-Pin Terminal Block 4(DI and DO)
Antenna Connector 2
P.O.E. PD port Present at ETH2
Fully compliant with IEEE 802.3af  Power Device specifi cation
Over load & short circuit protection
Isolation Voltage : 1000 VDC min.
Isolation Resistance : 108 ohms min
WLAN interface
Operating Mode AP/Bridge/Repeater/AP-Client
Antenna and connector Reverse SMA Female
Radio Frequency Type DSSS
Modulation IEEE802.11b: CCK, DQPSK, DBPSK
IEEE802.11g: OFDM with BPSK, QPSK, 16-QAM, 64-QAM
IEEE802.11n: OFDM with BPSK, QPSK, 16-QAM, 64-QAM
Frequency Band

America/FCC: 2.412~2.462 GHz (11 channels)
Europe CE/ETSI: 2.412~2.472 Ghz (13 channels)

Transmission Rate IEEE802.11b: 1/ 2/ 5.5/ 11 Mbps
IEEE802.11g: 6/ 9/ 12/ 18/ 24/ 36/ 48/ 54 Mbps
IEEE802.11n:up to 300Mbps
Transmit Power 802.11b: 17dBm ± 1.5dBm@11Mbps
802.11g: 16dBm ± 1.5dBm@54Mbps
802.11gn HT20: 15dBm ± 1.5dBm @MCS7
802.11gn HT40: 14dBm ± 1.5dBm @MCS7
Receiver Sensitivity 802.11b : -85dBm ± 2dBm@11Mbps
802.11g : -76dBm ± 2dBm@54Mbps
802.11gn HT20:-75dBm ± 2dBm@MCS7
802.11gn HT40:-72dBm ± 2dBm@MCS7
Encryption Security WEP: (64-bit ,128-bit key)
WPA/WPA2 PSK :TKIP and AES encryption (802.11i)
802.1X/RADIUS Authentication supported
Wireless Security SSID broadcast disable
Protocol Support
Protocol ARP, BOOTP, DHCP, DNS, HTTPs, IP, ICMP, SNTP, TCP, UDP, RADIUS, SNMP, STP (IEEE 802.1D)
LED Indicators
Power Indicator 3 x LEDs, PWR1(2)(PoE) / Ready:
Red On : Power is on and booting up
Green On : Power is on and functioning Normal
100/1000TX RJ45 Port Indicator 2 x LEDs,
LNK/ACT:Green for port Act.
Speed: Green for port Link at 1000Mbps
Amber for port Link at 100Mbps.
Off for port Link at 10Mbps
WLAN LEDs 1 x LED, Green for WLAN Link/ Act
Fault 1 x LED, Red for Ethernet link down or power down indicator
Fault contact
Relay Relay output to carry capacity of 1A at 24VDC
Power
Redundant Input Power Dual DC inputs. 12-48VDC on 6-pin terminal block Dual DC inputs. 12-48VDC on 6-pin terminal block
Power Consumption (Typ.) 7.5W 8.5W
Overload Current Protection Present
Reverse Polarity Protection Present
Physical Characteristic
Enclosure IP-30
Dimension (W x D x H) 74.3(W) x 109.2(D) x 153.6(H) mm (2.93 x 4.3 x 6.05 inch.)
Weight (g) 1150 1155
Environmental
Storage Temperature -40 to 85°C (-40 to 185°F)
Operating Temperature -25 to 70°C (-13 to 158°F)
Operating Humidity 5% to 95% Non-condensing
Regulatory approvals
EMI FCC Part 15, CISPR (EN55022) class A
EMS EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS),EN61000-4-8, EN61000-4-11
Shock IEC60068-2-27
Free Fall IEC60068-2-32
Vibration IEC60068-2-6
Safety EN60950-1
Warranty 5 years

Oring IGAP-420+ Industrial IEEE 802.11 b/g/n wireless access point with 2×10/100/1000 Base-T(X)

Posted on by

Oring IGAP-420+IGAP-420 is a reliable WLAN Access Point with 2 Ethernet Gigabit ports and IEEE 802.11 b/g/n wireless modules. It can be configured to operate in AP/Bridge/Repeater/AP-Client mode. You are able to configure IGAP-420 by WEB interface via LAN port or WLAN interface. IGAP-420 provides dual Ethernet ports in switch mode, so that you can use Daisy Chain to reduce the usage of Ethernet switch ports. In addition, IGAP-420 series also provides P.D. feature on ETH2 which is fully compliant with IEEE802.3af PoE P.D. specification. Therefore, IGAP-420 is one of the best communication solutions for wireless applications on the industrial network..

Feature :

  • High Speed Air Connectivity: WLAN interface support up to 300Mbps link speed
  • Highly Security Capability: WEP/WPA/WPA-PSK(TKIP,AES)/ WPA2/WPA2-PSK(TKIP,AES)/802.1X Authentication supported
  • Support X-Roaming < 60 ms
  • Support wireless load balance
  • Support MAC Filter
  • Support Long Distance Air Connectivity
  • Provide Digital Input and Digital Output
  • Support AP/Bridge/Repeater/AP-Client Mode
  • Switch Mode Supported: Daisy Chain support to reduce usage of switch ports
  • Dual redundant Ethernet port support redundant mode
  • Wireless connecting status monitoring
  • Secured Management by HTTPS
  • Event Warning by Syslog, Email, SNMP Trap, Relay and Beeper
  • Rigid IP-30 housing design
  • DIN-Rail and Wall-mount enabled

Specification :

IGAP-420 IGAP-420+
Physical Ports
100/1000Base-T(X) Ports in RJ45 Auto MDI/MDIX                                                                                     2
5-Pin Terminal Block 4(DI and DO)
Antenna Connector 2
P.O.E. PD port Present at ETH2
Fully compliant with IEEE 802.3af  Power Device specifi cation
Over load & short circuit protection
Isolation Voltage : 1000 VDC min.
Isolation Resistance : 108 ohms min
WLAN interface
Operating Mode AP/Bridge/Repeater/AP-Client
Antenna and connector Reverse SMA Female
Radio Frequency Type DSSS
Modulation IEEE802.11b: CCK, DQPSK, DBPSK
IEEE802.11g: OFDM with BPSK, QPSK, 16-QAM, 64-QAM
IEEE802.11n: OFDM with BPSK, QPSK, 16-QAM, 64-QAM
Frequency Band

America/FCC: 2.412~2.462 GHz (11 channels)
Europe CE/ETSI: 2.412~2.472 Ghz (13 channels)
Transmission Rate IEEE802.11b: 1/ 2/ 5.5/ 11 Mbps
IEEE802.11g: 6/ 9/ 12/ 18/ 24/ 36/ 48/ 54 Mbps
IEEE802.11n:up to 300Mbps
Transmit Power 802.11b: 17dBm ± 1.5dBm@11Mbps
802.11g: 16dBm ± 1.5dBm@54Mbps
802.11gn HT20: 15dBm ± 1.5dBm @MCS7
802.11gn HT40: 14dBm ± 1.5dBm @MCS7
Receiver Sensitivity 802.11b : -85dBm ± 2dBm@11Mbps
802.11g : -76dBm ± 2dBm@54Mbps
802.11gn HT20:-75dBm ± 2dBm@MCS7
802.11gn HT40:-72dBm ± 2dBm@MCS7
Encryption Security WEP: (64-bit ,128-bit key)
WPA/WPA2 PSK :TKIP and AES encryption (802.11i)
802.1X/RADIUS Authentication supported
Wireless Security SSID broadcast disable
Protocol Support
Protocol ARP, BOOTP, DHCP, DNS, HTTPs, IP, ICMP, SNTP, TCP, UDP, RADIUS, SNMP, STP (IEEE 802.1D)
LED Indicators
Power Indicator 3 x LEDs, PWR1(2)(PoE) / Ready:
Red On : Power is on and booting up
Green On : Power is on and functioning Normal
100/1000TX RJ45 Port Indicator 2 x LEDs,
LNK/ACT:Green for port Act.
Speed: Green for port Link at 1000Mbps
Amber for port Link at 100Mbps.
Off for port Link at 10Mbps
WLAN LEDs 1 x LED, Green for WLAN Link/ Act
Fault 1 x LED, Red for Ethernet link down or power down indicator
Fault contact
Relay Relay output to carry capacity of 1A at 24VDC
Power
Redundant Input Power Dual DC inputs. 12-48VDC on 6-pin terminal block Dual DC inputs. 12-48VDC on 6-pin terminal block
Power Consumption (Typ.) 7.5W 8.5W
Overload Current Protection Present
Reverse Polarity Protection Present
Physical Characteristic
Enclosure IP-30
Dimension (W x D x H) 74.3(W) x 109.2(D) x 153.6(H) mm (2.93 x 4.3 x 6.05 inch.)
Weight (g) 1150 1155
Environmental
Storage Temperature -40 to 85°C (-40 to 185°F)
Operating Temperature -25 to 70°C (-13 to 158°F)
Operating Humidity 5% to 95% Non-condensing
Regulatory approvals
EMI FCC Part 15, CISPR (EN55022) class A
EMS EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS),EN61000-4-8, EN61000-4-11
Shock IEC60068-2-27
Free Fall IEC60068-2-32
Vibration IEC60068-2-6
Safety EN60950-1
Warranty 5 years

Oring IAP-420+ Industrial IEEE 802.11 b/g/n wireless access point with 2×10/100Base-T(X)

Posted on by

Oring IAP-420+IAP-420 / IAP-420+ series are reliable 802.11 b/g/n WLAN Access Point with 2 ports LAN.  It supports 802.1X and MAC filters for security control.   It can be configured to operate in AP/Bridge/Repeater/AP-Client mode.  You are able to configure IAP-420 / IAP-420+ series by WEB interface via LAN port or WLAN interface.  In addition, IAP-420+ also provides P.D. feature on ETH1 which is fully compliant with IEEE802.3af PoE P.D. specification.  Therefore, IAP-420 / IAP-420+ series are one of the best communication solutions for wireless applications on the industrial network.

Feature :

  • High Speed Air Connectivity: WLAN interface support up to 150 Mbps link speed
  • Highly Security Capability: WEP/WPA/WPA-PSK(TKIP,AES)/ WPA2/WPA2-PSK(TKIP,AES)/802.1X Authentication supported
  • Support X-Roaming < 100 ms
  • Support AP/Client/Bridge/AP-Client Mode
  • Secured Management by HTTPs
  • Wireless connecting status monitoring
  • Event Warning by Syslog, Email, SNMP Trap
  • 1KV isolation for PoE P.D. port of IAP-420+
  • Rigid IP-30 housing design
  • DIN-Rail and Wall-mount enabled

Specification :

IAP-420 IAP-420+
Physical Ports
10/100Base-T(X) Ports in RJ45 Auto MDI/MDIX                                                                                     2
P.O.E. PD port Present at ETH1
Fully compliant with IEEE 802.3af  Power Device specifi cation
Over load & short circuit protection
Isolation Voltage : 1000 VDC min.
Isolation Resistance : 108 ohms min
WLAN interface
Operating Mode AP/Bridge/AP-Client
Antenna Connector 1 x External reverse SMA-type antenna connector
Radio Frequency Type DSSS, OFDM
Modulation IEEE802.11b: CCK, DQPSK, DBPSK
IEEE802.11g/n: OFDM with BPSK, QPSK, 16QAM, 64QAM
Frequency Band America/FCC: 2.412~2.462 GHz (11 channels)
Europe CE/ETSI: 2.412~2.472 Ghz (13 channels)
Transmission Rate 802.11b: 1/2/5.5/11 Mbps
802.11g: 6/9/12/18/24/36/48/54 Mbps
802.11n(40MHz): UP to 150 Mbps
Transmit Power 802.11b: 13.5dBm ±1.5dBm
802.11g: 13.5dBm ±1.5dBm
802.11n(2.4G@20MHz): 13.5dBm ±1.5dBm
802.11n(2.4G@40MHz): 13.5dBm ±1.5dBm
Receiver Sensitivity 802.11b: -90dBm ±2dBm@1Mbps
802.11g: -72dBm ±2dBm@54Mbps
802.11n(2.4G@40MHz,MCS7): -68dBm ±2dBm
Encryption Security WEP: (64-bit, 128-bit key supported)
WPA/WPA2:802.11i (WEP and AES encryption)
WPA-PSK (256-bit key pre-shared key supported)
802.1X Authentication supported
TKIP encryption
Wireless Security SSID broadcast disable and enable
Protocol Support
Protocol ARP,BOOTP, DHCP, DNS, HTTP, IP, ICMP, SNTP, TCP, UDP, 802.1X, SNMP, STP
LED Indicators
Power Indicator LED x 3, PWR 1, 2, (PoE):
Green On: Power is on and functioning Normally.
100/1000TX RJ45 Port Indicator LED x 2 , Green for port Link/Act at 100Mbps.
WLAN LEDs WLAN Link /ACT: Green: Link,
Power
Redundant Input Power Dual DC inputs.  12~48VDC on 4-pin terminal block
Power Consumption (Typ.) 4watts
Overload Current Protection Present
Reverse Polarity Protection Present
Physical Characteristic
Enclosure IP-30
Dimension (W x D x H) 41(W) x 81(D) x 95(H) mm (1.6 x 3.1 x 3.7 inch.)
Weight (g) 292 297
Environmental
Storage Temperature -40 to 85°C (-40 to 185°F)
Operating Temperature -10 to 60oC (14 to 140oF)
Operating Humidity 5% to 95% Non-condensing
Regulatory approvals
EMI FCC Part 15, CISPR (EN55022) class A
EMS EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS),EN61000-4-8, EN61000-4-11
Shock IEC60068-2-27
Free Fall IEC60068-2-31
Vibration IEC60068-2-6
Safety EN60950-1
Warranty 3 years