TRENDnet TV-VS1 Single Channel Analog to IP Video Encoder

• Advanced IP-based functionality for an analog CCTV security camera
• View a CCTV camera from any Internet connection and on compatible mobile phones
• Motion detection recording, email alerts, and alarm triggers
• Schedule recording sessions to a server with Samba client support

Feature :

• 1 x 10/100Mbps Auto-MDIX RJ-45 port
• SD/SDHC card slot *
• BNC video out and video in connectors
• Audio support : built-in Audio jacks for additional 3rd party microphone and speaker
• Input/Output ports (GPIO) to network to alarm systems
• Diagnostic Power and Link LEDs
• Four installation mounting points
• 3x digital zoom
• Pelco D and Pelco P pan/tilt/zoom support: Define Auto-Patrol pan tilt with up to 32 viewing nodes
• High quality H.264, MPEG-4, and MJPEG video recording
• Resolution up to 704 x 576 pixels and up to 30 frames per second (fps)
• Stream Network camera video to a 3GPP compatible wireless device
• Dynamic DNS support
• Images controls: brightness, saturation, contrast, Hue ,and Wide Dynamic Range Correction (WDRC)
• Time, date, and other text overlays
• Mask overlays conceal sensitive areas
• Supports TCP/IP networking, SMTP Email, HTTP, and other Internet protocols
• Recording type: continuous, schedule, or motion detection
• Record streaming video to your computer or Network Storage device with Samba support
• Three motion detection windows with just-in-time snapshot , motion detection triggered email alerts, and image upload to FTP
• Event trigger: motion detection or Input/Output signal
• Event response: email alert, instant snapshot, or video recording
• Send instant messages to Jabber client via Jabber Server
• Supports Quality of Service (QoS) with Differentiated Services Code Point (DSCP)
• Quick Universal Plug and Play (UPnP) installation
• 3-year limited warranty

Diagram :Specification :

General

• Video
  • Video In: CVBS / 1 Vp-p±0.2 / 75 Ohms ; BNC connecter
  • Video Out: CVBS /1 Vp-p /75 Ohms; BNC connecter
• Audio
  • Line In: 3.5mm jack ( CCTV audio)
  • Line Out: 3.5mm jack (Speaker)
  • S/N Ratio: < 60dB
  • Codec: PCM/AMR
  • 2 Way audio supported
• GPIO
  • Ground, GPIO in/out, DV12V output, RS485 TX+/TX-
• SD Slot
  • Supports SD/SDHC (up to 32GB)
• Pan/Tilt/Zoom
  • Protocol: Pelco D, Pelco P
  • 32 presets
  • Auto Patrol

Hardware

• Network
  • IEEE 802.3u 10/100Mbps Fast Ethernet, Auto-MDIX
• LED
  • Power, Link
• Reset Button
  • Push and release to reboot
  • Push and hold for 5 seconds to restore to factory default
• Power Consumption
  • 7 Watts
• Power
  • 12V, 1.5A external power adapter
• Dimension
  • 160 x 109 x 36 mm (6.3 x 4.3 x 1.4 in.)
• Weight
  • 430 g (15.2 oz.)
• Temperature
  • Operating: 0°C ~ 45°C (32°F ~ 113°F)
  • Storage: -15°C ~ 60°C (5°F ~ 140°F)
• Humidity
  • Max. 85% (non-condensing)
• Certifications
• CE, FCC

Requirement

• Management Interface
  • Internet Explorer 6.0 or above
• To run Utility
  • Windows 7(32/64-bit), Vista(32/64-bit), XP(32/64-bit)
• Network Protocols
  • TCP/IP, IPv4/IPv6, UDP, ICMP, DHCP, NTP, DNS, DDNS, SMTP, FTP, HTTP, HTTPs, Samba, PPPoE, UPnP, Bonjour, RTP, RTSP, RTCP

Management

• Remote
  • Remote management supported
• Backup / Restore
  • Save/retrieve configuration files

Settings

• Image
  • Brightness, contrast, saturation, Hue, WDRC (Wide Dynamic Range Correction)
• Video Encoder
  • Encoding type: H.264, MPEG4, MJPEG
  • Resolution/Frame rate(auto-sensing)704 x 480, 352 x 240, 176 x 120, up to 30 fps (NTSC)
  • 704 x 576, 352 x 288, 176 x 144, up to 25 fps (PAL)
  • Compression: 5 levels
• Recording
  • Recording type: continuous, schedule, or motion detection
• Port Settings
  • HTTP port: 80 (default), RTSP (554)
• Digital Zoom
  • 3x
• Dynamic DNS
  • Yes
• Time
  • Synchronize with NTP server or set time/date manually
• SMTP
  • Supported up to 2 destination email accounts
• System Log
  • 100 entries