Oring TGAP-620-M12 Industrial EN50155 IEEE 802.11 a/b/g/n wireless access point with 2×10/100/1000Base-T(X), M12 connector

by | Jun 25, 2015 | ORing, Transpoter Wirelles Product

Oring TGAP-620-M12ORing’s TransporterTM series access point is designed for industrial and rolling stock wireless applications, such as vehicle, and railway applications. TGAP-620-M12 is a reliable 802.11 a/b/g/n WLAN Access Point with 2 Ethernet 10/100/1000 ports. It can be configured to operate in AP/Client /Bridge /AP-Client Mode. TGAP-620-M12 provides dual Ethernet ports in switch mode, so that you can use Daisy Chain to reduce the usage of Ethernet switch ports. TGAP-620-M12 provides a dust-tight connection and reverses SMA-type connectors that can install any reverse SMA-type antennas to extend communication distance. It is specifically designed for the toughest industrial environments. You are able to configure TGAP-620-M12 by WEB interface via LAN port or WLAN interface. TGAP-620-M12 can be easily adopted in almost all kinds of applications and provides the most rugged solutions for managing your network in outdoor. In addition, TGAP-620+-M12 also provides P.D. feature on ETH2 which is fully compliant with IEEE802.3af PoE P.D. specification. Therefore, TGAP-620-M12 is one of the best communication solutions for wireless applications.

Feature :

  • High Speed Air Connectivity: WLAN interface support up to 300 Mbps link speed
  • Highly Security Capability: WEP/WPA/WPA-PSK(TKIP,AES)/ WPA2/WPA2-PSK(TKIP,AES)/802.1X Authentication supported
  • Dual Gigabit Ethernet ports support Ethernet redundant mode (Recovery time < 10ms) and switch mode in M12 connector (A-coding)
  • Support X-Roaming < 60 ms
  • Support wireless load balance
  • Support Multiple-SSID to 4 SSID
  • Support external SMA antenna installation
  • Support AP/Client /Bridge /AP-Client Mode
  • Support MAC Filter
  • Dual Ethernet ports support Ethernet redundant mode (Recovery time < 10ms) and switch mode in M12 connector (A-coding)
  • Wireless connecting status monitoring
  • 1KV isolation for PoE P.D. port for TGAP-620+-M12 • Secured Management by HTTPS
  • Event Warning by Syslog, Email, SNMP Trap, and Relay output
  • Rigid IP-40 housing design
  • Wall-mount enabled

Specification :

TGAP-620-M12 TGAP-620+-M12
Physical Ports
100/1000Base-T(X) Ports in M12 Auto MDI/MDIX (8-pin A-coding) 2 2 (Present at ETH2 Fully Compiant with IEEE 802.3af PoE P.D.)
DIDO port in M12 (A-Coding) 2(DI x 4 and DO x 4)
Dry Contact:
On: short to GND, off: open
Wet Contact(DI to COM/GND):
On: 0 to 3VDC, off: 10 to 30VDC
RS-232 Console port in M12 (5-pin A-coding) 115200, 8 ,N ,1
Antenna Connector 2
 Relay port in M12 (5-pin A-coding)  1A@24VDC
WLAN interface
Operating Mode AP/Bridge/Repeater/AP-Client
Antenna and connector 2 x Reverse SMA Female
Radio Frequency Type DSSS
Modulation IEEE802.11b: CCK, DQPSK, DBPSK
IEEE802.11a/g: OFDM with BPSK, QPSK, 16-QAM, 64-QAM
IEEE802.11n: OFDM with BPSK, QPSK, 16-QAM, 64-QAM
Frequency Band

America/FCC: 2.412~2.462 GHz (11 channels)
5.180~5.240 GHz & 5.745~5.825 GHz (9 channels)
Europe CE/ETSI: 2.412~2.472 Ghz (13 channels)
5.180~5.240 GHz  (4 channels)
Transmission Rate IEEE802.11b: 1 / 2 / 5.5 / 11 Mbps
IEEE802.11a/g: 6 / 9 / 12 / 18 / 24 / 36 / 48 / 54 Mbps
IEEE801.11n: up to 300Mbps
Transmit Power 802.11a: 12dBm ± 1.5dBm
802.11b: 18dBm ± 1.5dBm
802.11g: 15dBm ± 1.5dBm
802.11gn HT20: 13dBm ± 1.5dBm@150Mbps
802.11gn HT40: 12dBm ± 1.5dBm@300Mbps
802.11an HT20: 12dBm ± 1.5dBm@150Mbps
802.11an HT40: 12dBm ± 1.5dBm@300Mbps
Receiver Sensitivity 802.11a: -68dBm ±2dBm@54Mbps
802.11b: -85dBm ±2dBm@11Mbps
802.11g: -68dBm ±2dBm@54Mbps
802.11gn HT20: -68dBm ±2dBm@150Mbps
802.11gn HT40: -68dBm ±2dBm@300Mbps
802.11an HT20: -68dBm ±2dBm@150Mbps
802.11an HT40: -68dBm ±2dBm@300Mbps
Encryption Security WEP: (64-bit ,128-bit key supported)
WPA/WPA2 :802.11i(WEP and AES encryption)
WPAPSK (256-bit key pre-shared key supported)
802.1X Authentication supported
TKIP encryption
Wireless Security SSID broadcast disable and enable
Protocol Support
Protocol ARP,BOOTP, DHCP, DNS, HTTP, IP, ICMP, SNTP, TCP, UDP, RADIUS, SNMP, STP, RSTP
LED Indicators
Power Indicator 2 x LEDs, Green for Power on
10/100/1000TX RJ45 Port Indicator 2 x LEDs, Green for port Link/Act
WLAN LED 1 x LED, Green for WLAN Link/Act
Fault 1 x LED, Red for Ethernet link down or power down indicator
Fault contact
Relay Relay output to carry capacity of 1A at 24VDC(5-pin M12 A-coding)
Power
Redundant Input Power Dual Power Inputs. 12~48 VDC
Power Consumption (Typ.) 7 Watts 7.5 Watts
Physical Characteristic
Enclosure IP-40
Dimension (W x D x H) 125.6(W) x 65(D) x 196.1(H) mm (4.94 x 2.55 x 7.72 inch.)
Weight (g) 965 g 970 g
Environmental
Storage Temperature -40 to 85°C (-40 to 185°F)
Operating Temperature -25 to 70°C (-13 to 158°F)
Operating Humidity 5% to 95% Non-condensing
Regulatory approvals
EMI FCC Part 15, CISPR (EN55022) class A, EN50155 (EN50121-3-2, EN55011, EN50121-4)
EMS EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
Shock IEC60068-2-27, EN61373
Free Fall IEC60068-2-31
Vibration IEC60068-2-6, EN61373
Safety EN60950-1
Warranty 5 years

Related Posts