Oring TAP-3120-M12ORing’s TransporterTM series access point is designed for industrial and rolling stock wireless applications, such as vehicle, and railway applications.  TAP-3120-M12 is a reliable IEEE802.11 a/b/g and 802.11b/g WLAN Access Point with 2 ports LAN which is fully compliant with EN50155 certification.  TAP-3120-M12 access point use M-series connectors to ensure tight, robust connections, and guarantee reliable operation against environmental disturbances, such as vibration and shock.  TAP-3120-M12 provides dual-RF wireless interfaces, which can provide IEEE 802.11 a/b/g and 802.11b/g dual band wireless communication and can be applied to fulfill any demands of wireless applications.  TAP-3120-M12 can be configured to operate in Dual AP/Dual Client/Bridge/AP-Client mode.  TAP-3120-M12 provides dual Ethernet ports in switch mode, so that you can use Daisy Chain to reduce the usage of Ethernet switch ports. You are able to configure TAP-3120-M12 by WEB interface via LAN port or WLAN interface. Therefore, TAP-3120-M12 is one of the most reliable choices for rolling stock applications on the wireless network.

Feature :

  • Leading EN50155-compliant wireless access point for rolling stock application
  • Dual high Speed Air Connectivity: WLAN interface support up to 54Mbps link speed
  • Highly Security Capability: WEP/WPA/WPA-PSK(TKIP,AES)/ WPA2/WPA2-PSK(TKIP,AES)/802.1X Authentication supported
  • Support X-Roaming < 100 ms
  • Support wireless load balance
  • Support Dual AP/Dual Client/Bridge/AP-Client Mode
  • Provide dual-RF which support IEEE 802.11 a/b/g and 802.11 b/g dual band for wireless communication
  • Dual redundant Ethernet ports support Ethernet redundant mode (Recovery time < 10ms) and switch mode in M12 connector (D-coding)
  • Wireless connecting status monitoring
  • Secured Management by HTTPS
  • Event Warning by Syslog, Email, SNMP Trap and Relay output
  • Ultra rugged enclosure for toughest industrial usages
  • Wall mounting enabled

Specification :

ORing EN50155 Access Point Model TAP-3120-M12
Physical Ports
10/100Base-T(X) Ports in M12 Auto MDI/MDIX 2 (4-pin M12 connetor – D-coding)
WLAN Interface
Operating Mode Dual AP/Dual Client/Bridge/Repeater/AP-Client
Antenna and Connector 4 x 2 dBi (b/g mode) / 3dBi (a mode) on Reverse SMA connector
Radio Frequency Type DSSS, OFDM
Modulation IEEE802.11a: OFDM with BPSK, QPSK, 16QAM, 64QAM
IEEE802.11b: CCK, DQPSK, DBPSK
IEEE802.11g: OFDM with BPSK, QPSK, 16QAM, 64QAM
Frequency Band America / FCC: 2.412~2.462 GHz (11 channels)
5.15 to 5.825 GHz (13 channels)
Europe CE / ETSI: 2.412~2.472 Ghz (13 channels)
5.15 to 5.724 GHz (19 channels)
Transmission Rate IEEE802.11b : 1/ 2/ 5.5/ 11 Mbps
IEEE802.11a/g : 6/ 9/ 12/ 18/ 24/ 36/ 48/ 54 Mbps
Transmit Power IEEE802.11a/b/g : 20dBm max
Receiver Sensitivity 802.11a: -77dBm±2.0dB @ 54Mbps, PER< 10%
802.11b: -86dBm±1.5dB @ 11Mbps, PER< 8%;
802.11g: -78dBm±1.5dB @ 54Mbps, PER< 10%
Encryption Security WEP : (64-bit ,128-bit key supported)
WPA / WPA2 : 802.11i(WEP and AES encryption)
WPA-PSK (256-bit key pre-shared key supported)
802.1X Authentication supported
TKIP encryption
Wireless Security SSID broadcast disable
Protocol Support
Protocol ARP,BOOTP, DHCP, DNS, HTTP, IP, ICMP, SNTP, TCP, UDP, RADIUS, SNMP, PPPoE, STP (IEEE 802.1D)
LED Indicators
Power Indicator 2 x LEDs, Green for Power Indicator
10/100Base-T(X) Port Indicator 2 x LEDs, Green for port Link/Act at 100Mbps, Amber for port Link/Act at 10Mbps
WLAN LEDs 2 x LEDs, Green for WLAN 1 and WLAN 2 Link/Act
Fault Indicator 1 x LED, Red for Ethernet link down or power down indicator
Fault contact
Relay Relay output to carry capacity of 3A at 24VDC(5-pin M12 A-Coding)
Power
Redundant Input Power Dual Power Inputs. 12~48 VDC on 5-pin M23 connector (24 VDC Typ.)
Power Consumption (Typ.) 8.3W
Overload Current Protection Present
Reverse Polarity Protection Present
Physical Characteristic
Enclosure IP-40
Dimension (W x D x H) 125(W) x 65(D) x 196(H) mm (4.92 x 2.56 x 7.72 inch.)
Weight (g) 1015g
Environmental
Storage Temperature -40 to 85°C (-40 to 185°F)
Operating Temperature -20 to 70°C (-4 to 158°F)
Operating Humidity 5% to 95% Non-condensing
Regulatory approvals
EMI FCC Part 15, CISPR (EN55022) class A, EN50155 (EN50121-3-2)
EMS EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
Shock IEC60068-2-27, EN61373
Free Fall IEC60068-2-32
Vibration IEC60068-2-6 , EN61373
Safety EN60950-1
Warranty 3 years