Oring IPMC-111PBIPMC-111PB is a cost-effective solution for the conversion interface between 10/100Base-T(X) and 100Base-FX, it allows you to extend communication distance by optical fiber. IPMC-111PB supports MDI/MDIX auto detection, so you don’t need to use crossover wires. IPMC-111PB also support Power over Ethernet, a system to transmit electrical power up to 30 watts, along with data, to remote devices over standard twisted-pair cable in an Ethernet network. Each IPMC-111PB has 1×10/100Base-T(X) P.S.E. (Power Sourcing Equipment) port to provide power in a PoE setup. IPMC-111PB with wide operating temperature range from -40°C~70°C and accepts a wide voltage range from dual 50~57 VDC power inputs, so it is suitable for harsh operating environments.

IPMC-111PB also supports the LFP (Link Fault Pass-through) feature. When one side of the link fails, the other side continues transmitting packets, and waiting for a response that never arrives from the disconnected side. Use the DIP-Switch to enable the LFP function, then IPMC-111PB will force the link to shutdown as soon as noticed that the other link has failed, to notice the administrator to react to the situation. Therefore, the IPMC-111PB is reliable media converter with PoE capability and can satisfy most demand of operating environment

Feature :

  • Supports 1 port 10/100Base-T(X) auto-negotiation and auto-MDI/MDI-X
  • Supports Ethernet to fiber with SFP socket
  • Support LFP (Link Fault Pass-through) function
  • Supports full/half duplex operation mode
  • P.S.E. fully compliant with IEEE802.3at standard, provide up to 30 Watts
  • Supports store and forward transmission
  • Provided DIP-Switch to set operation mode
  • High reliability and rigid IP-30 housing
  • DIN-Rail and panel mounting enabled

Specification :

ORing Media Converter Model IPMC-111PB
Physical Ports
10/100Base-T(X) Ports in RJ45 Auto MDI/MDIX 1
Technology
Ethernet Standards IEEE 802.3 for 10Base-T
IEEE 802.3u for 100Base-TX and 100Base-FX
IEEE 802.3x for Flow control
IEEE 802.3at PoE specification (up to 30 Watts per port for P.S.E.)
Processing Store-and-Forward
DIP-Switch setting DIP-Switch 1 for LFP mode selection : (ON) enable / (OFF) disable
DIP-Switch 2 for Ethernet speed selection : (ON)10Mbps / (OFF) 10/100Mbps Auto-negotiate
DIP-Switch 3 for Ethernet full/half duplex selection : (ON) Half-duplex / (OFF) Full/Half-Duplex Auto-negotiate
DIP-Switch 4 for fiber full/half duplex selection : (ON) Half-Duplex / (OFF) Full-Duplex
LED Indicators  
Power indicator Green : Power LED x 2 (ON : power input on-line / (OFF) power input off-line
10/100Base-T(X) RJ45 port indicator Green for port Link/Act – (ON) Link up / (Blinking) Acting / (OFF) Link down
Amber for 100Mbps/10Mbps indicator – (ON) Working at 100Mbps / (OFF) Working at 10Mbps
Green for port duplex indicator – (ON) Full-Duplex / (OFF) Half-Duplex
100Base-FX fiber port indicator Green for fiber port Link/Act – (ON) Link up / (Flash) Acting / (OFF) Link down
Green for fiber port duplex indicator – (ON) Full-Duplex / (OFF) Half-Duplex
LFP statue indicator Amber LED – (ON) LFP function fail / (OFF) LFP function disable
PoE indicator Amber for P.S.E. indicator
Power
Input power Dual 50~57 VDC voltage power inputs at 4-pin terminal block
Power consumption (Typ.) 31.2 Watts (P.S.E. output included)
Overload current protection Present
Reverse polarity protection Present
Physical Characteristic
Enclosure IP-30
Dimension (W x D x H) 26.1 (W) x 70 (D) x 95 (H)mm (1.03 x 2.76 x 3.74 inch)
Weight (g) 210 g
Environmental
Storage Temperature -40 to 85°C(-40 to 185°F)
Operating Temperature -40 to 70°C (-40 to 158°F)
Operating Humidity 5% to 95% Non-condensing
Regulatory approvals
EMI FCC Part 15, CISPR (EN55022) class A, EN50155 (EN50121-3-2, EN55011, EN50121-4)
EMS EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS), EN61000-4-8,
EN61000-4-11
Shock IEC60068-2-27
Free Fall IEC60068-2-32
Vibration IEC60068-2-6
Safety EN60950-1
Warranty 5 years