IGAP-420 is a reliable WLAN Access Point with 2 Ethernet Gigabit ports and IEEE 802.11 b/g/n wireless modules. It can be configured to operate in AP/Bridge/Repeater/AP-Client mode. You are able to configure IGAP-420 by WEB interface via LAN port or WLAN interface. IGAP-420 provides dual Ethernet ports in switch mode, so that you can use Daisy Chain to reduce the usage of Ethernet switch ports. In addition, IGAP-420 series also provides P.D. feature on ETH2 which is fully compliant with IEEE802.3af PoE P.D. specification. Therefore, IGAP-420 is one of the best communication solutions for wireless applications on the industrial network..
Feature :
- High Speed Air Connectivity: WLAN interface support up to 300Mbps link speed
- Highly Security Capability: WEP/WPA/WPA-PSK(TKIP,AES)/ WPA2/WPA2-PSK(TKIP,AES)/802.1X Authentication supported
- Support X-Roaming < 60 ms
- Support wireless load balance
- Support MAC Filter
- Support Long Distance Air Connectivity
- Provide Digital Input and Digital Output
- Support AP/Bridge/Repeater/AP-Client Mode
- Switch Mode Supported: Daisy Chain support to reduce usage of switch ports
- Dual redundant Ethernet port support redundant mode
- Wireless connecting status monitoring
- Secured Management by HTTPS
- Event Warning by Syslog, Email, SNMP Trap, Relay and Beeper
- Rigid IP-30 housing design
- DIN-Rail and Wall-mount enabled
Specification :
IGAP-420 | IGAP-420+ | |
Physical Ports | ||
100/1000Base-T(X) Ports in RJ45 Auto MDI/MDIX | 2 | |
5-Pin Terminal Block | 4(DI and DO) | |
Antenna Connector | 2 | |
P.O.E. PD port | Present at ETH2 Fully compliant with IEEE 802.3af Power Device specifi cation Over load & short circuit protection Isolation Voltage : 1000 VDC min. Isolation Resistance : 108 ohms min |
|
WLAN interface | ||
Operating Mode | AP/Bridge/Repeater/AP-Client | |
Antenna and connector | Reverse SMA Female | |
Radio Frequency Type | DSSS | |
Modulation | IEEE802.11b: CCK, DQPSK, DBPSK IEEE802.11g: OFDM with BPSK, QPSK, 16-QAM, 64-QAM IEEE802.11n: OFDM with BPSK, QPSK, 16-QAM, 64-QAM |
|
Frequency Band |
America/FCC: 2.412~2.462 GHz (11 channels) |
|
Transmission Rate | IEEE802.11b: 1/ 2/ 5.5/ 11 Mbps IEEE802.11g: 6/ 9/ 12/ 18/ 24/ 36/ 48/ 54 Mbps IEEE802.11n:up to 300Mbps |
|
Transmit Power | 802.11b: 17dBm ± 1.5dBm@11Mbps 802.11g: 16dBm ± 1.5dBm@54Mbps 802.11gn HT20: 15dBm ± 1.5dBm @MCS7 802.11gn HT40: 14dBm ± 1.5dBm @MCS7 |
|
Receiver Sensitivity | 802.11b : -85dBm ± 2dBm@11Mbps 802.11g : -76dBm ± 2dBm@54Mbps 802.11gn HT20:-75dBm ± 2dBm@MCS7 802.11gn HT40:-72dBm ± 2dBm@MCS7 |
|
Encryption Security | WEP: (64-bit ,128-bit key) WPA/WPA2 PSK :TKIP and AES encryption (802.11i) 802.1X/RADIUS Authentication supported |
|
Wireless Security | SSID broadcast disable | |
Protocol Support | ||
Protocol | ARP, BOOTP, DHCP, DNS, HTTPs, IP, ICMP, SNTP, TCP, UDP, RADIUS, SNMP, STP (IEEE 802.1D) | |
LED Indicators | ||
Power Indicator | 3 x LEDs, PWR1(2)(PoE) / Ready: Red On : Power is on and booting up Green On : Power is on and functioning Normal |
|
100/1000TX RJ45 Port Indicator | 2 x LEDs, LNK/ACT:Green for port Act. Speed: Green for port Link at 1000Mbps Amber for port Link at 100Mbps. Off for port Link at 10Mbps |
|
WLAN LEDs | 1 x LED, Green for WLAN Link/ Act | |
Fault | 1 x LED, Red for Ethernet link down or power down indicator | |
Fault contact | ||
Relay | Relay output to carry capacity of 1A at 24VDC | |
Power | ||
Redundant Input Power | Dual DC inputs. 12-48VDC on 6-pin terminal block | Dual DC inputs. 12-48VDC on 6-pin terminal block |
Power Consumption (Typ.) | 7.5W | 8.5W |
Overload Current Protection | Present | |
Reverse Polarity Protection | Present | |
Physical Characteristic | ||
Enclosure | IP-30 | |
Dimension (W x D x H) | 74.3(W) x 109.2(D) x 153.6(H) mm (2.93 x 4.3 x 6.05 inch.) | |
Weight (g) | 1150 | 1155 |
Environmental | ||
Storage Temperature | -40 to 85°C (-40 to 185°F) | |
Operating Temperature | -25 to 70°C (-13 to 158°F) | |
Operating Humidity | 5% to 95% Non-condensing | |
Regulatory approvals | ||
EMI | FCC Part 15, CISPR (EN55022) class A | |
EMS | EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS),EN61000-4-8, EN61000-4-11 | |
Shock | IEC60068-2-27 | |
Free Fall | IEC60068-2-32 | |
Vibration | IEC60068-2-6 | |
Safety | EN60950-1 | |
Warranty | 5 years |