Nport 54104-port RS-232 serial device servers

NPort 5400 series device servers can conveniently and transparently connect up to four serial devices to an Ethernet network, allowing you to network your existing serial devices with only basic configuration. Data transmission between the serial and Ethernet interfaces is bi-directional. By using NPort device servers, you not only protect your current hardware investment, but also allow for future network expansion. You can both centralize the management of your serial devices, and distribute management hosts over the network.

Independent Operation Mode for Each Serial Port

NPort 5400 series device servers can be used to connect different devices for remote data polling or event handling over a TCP/IP network. Each serial port on the NPort 5400 series operates independently to provide maximum versatility. For example, port 1 can operate in Driver mode, port 2 in TCP Server mode, and ports 3 and 4 in TCP Client mode.

User-friendly LCD Panel for Easy Installation

An LCD panel is built into the NPort 5400’s top panel, with four buttons for inputting data, configuration, and selecting the operation mode. The LCD panel displays the server name, serial number, and IP address, and can be used to enter or modify parameters such as IP address, netmask, and gateway. (The LCD panel is not available on wide temperature models.)

Dual DC Power Inputs

NPort 5400 device servers support dual power sources by providing both a DC terminal block input and a DC power jack input. Providing two types of power input gives users greater flexibility for use with different applications.

Adjustable Termination and Pull High/Low Resistors

The NPort 5400 series provides adjustable termination and pull high/low resistors for RS-485 applications. In some critical environments, termination resistors may be needed to prevent the reflection of serial signals, and the pull high/low resistors may need adjusting to maintain the integrity of the electrical signal. Since no set of resistor values is universally compatible with all environments, the NPort® 5400 has four sets of DIP switches on the bottom panel to set the termination and pull high/low resistor values.

Feature :

Features and Benefits

  • 10/100M auto-sensing Ethernet
  • 4 serial ports, with support for RS-232, RS-422, and RS-485
  • Built-in 15 KV ESD surge protection for all serial signals
  • Versatile socket operation modes, including TCP Server, TCP Client, UDP, and Real COM
  • Choice of configuration methods: Web console, Telnet console, and Windows utility
  • SNMP MIB-II for network management
  • 2 KV isolation protection for NPort 5430I/5450I/5450I-T
  • -40 to 75°C operating temperature range (T model)
  • Supports Moxa’s MXview industrial network management software via the MXview Plug-in

Diagram :

Nport 5410-1

Nport 5410-2

Nport 5410-3

Specification :

• Ethernet Interface
Number of Ports 1
Speed 10/100 Mbps, auto MDI/MDIX
Connector 8-pin RJ45
Magnetic Isolation Protection 1.5 KV built-in
• Serial Interface
Number of Ports 4
Serial Standards NPort 5410: RS-232
NPort 5430/5430I: RS-422/485 (software selectable)
NPort 5450/5450I/5450-T/5450I-T: RS-232/422/485 (software selectable)
Connector NPort 5410/5450/5450I/5450-T/5450I-T: DB9 male
NPort 5430/5430I: Terminal block
Serial Line Protection 15 KV ESD protection for all signals
2 KV isolation protection (NPort 5430I/5450I/5450I-T)
RS-485 Data Direction Control ADDC® (automatic data direction control)
Pull High/Low Resistor for RS-485 1 KΩ, 150 KΩ
Terminator for RS-485 120 Ω
• Serial Communication Parameters
Data Bits 5, 6, 7, 8
Stop Bits 1, 1.5, 2
Parity None, Even, Odd, Space, Mark
Flow Control RTS/CTS and DTR/DSR (RS-232 only), XON/XOFF
Baudrate 50 bps to 921.6 Kbps
• Serial Signals
RS-232 TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS-422 Tx+, Tx-, Rx+, Rx-, GND
RS-485-4w Tx+, Tx-, Rx+, Rx-, GND
RS-485-2w Data+, Data-, GND
• Software
Network Protocols ICMP, IP, TCP, UDP, DHCP, BOOTP, Telnet, DNS, SNMP V1, HTTP, SMTP, SNTP, Rtelnet, ARP
Configuration Options Web Console, Telnet Console, Windows Utility
Windows Real COM Drivers Windows 95/98/ME/NT/2000, Windows XP/2003/Vista/2008/7/8 x86/x64, 2012 x64, Embedded CE 5.0/6.0, XP Embedded
Fixed TTY Drivers SCO Unix, SCO OpenServer, UnixWare 7, UnixWare 2.1, SVR 4.2, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i
Linux Real TTY Drivers Linux kernel 2.4.x, 2.6.x, 3.x
• Mini Screen with Push Buttons (standard temp. models only)
LCD Panel Liquid Crystal Display on the case
Push Buttons Four push buttons for convenient on-site configuration
• Physical Characteristics
Housing Metal, IP30 protection
Weight 740 g
Dimensions Without mounting kit: 158 x 103 x 33 mm (6.22 x 4.06 x 1.30 in)
With mounting kit: 176 x 103 x 33 mm (6.93 x 4.06 x 1.30 in)
• Environmental Limits
Operating Temperature Standard Models: 0 to 55°C (32 to 131°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Storage Temperature -40 to 75°C (-40 to 167°F)
Ambient Relative Humidity 5 to 95% (non-condensing)
• Power Requirements
Input Voltage 12 to 48 VDC
Power Consumption NPort 5410: 350 mA @ 12 V, 190 mA @ 24 V
NPort 5430: 320 mA @ 12 V, 175 mA @ 24 V
NPort 5430I: 530 mA @ 12 V, 280 mA @ 24 V
NPort 5450/5450-T: 350 mA @ 12 V, 190 mA @ 24 V
NPort 5450I/5450I-T: 554 mA @ 12 V, 294 mA @ 24 V
• Standards and Certifications
Safety UL 60950-1, EN 60950-1
EMC CE, FCC
EMI EN 55022 Class A, FCC Part 15 Subpart B Class A
EMS EN 55024
Marine DNV (standard temp. models only)
Medical EN 60601-1-2 Class B, EN 55011
• Reliability
Alert Tools Built-in buzzer and RTC (real-time clock)
Automatic Reboot Trigger Built-in WDT (watchdog timer)
MTBF (mean time between failures) NPort 5410: 205,153 hrs
NPort 5430: 201,699 hrs
NPort 5430I: 114,540 hrs
NPort 5450/5450I: 206,903 hrs
NPort 5450-T/5450I-T: 206,903 hrs
• Warranty
Warranty Period 5 years
Details See http://www.moxa.com/support/warranty.htm